Updated November 2026

Two story birdhouse plans give you a single box with two separate compartments, so two pairs of birds can nest in one structure without sharing space. This guide walks through the dimensions, cut list, and assembly order for a basic two-story build in cedar or pine. You will finish with a box that has a stacked design, proper entry holes, and a floor that drains and can be cleaned.

Choose Materials and Dimensions Before You Cut

Use rough cedar, pine, or another untreated softwood at least 3/4 inch thick. Thinner stock dries out, warps, and holds heat poorly. Avoid pressure-treated lumber, painted surfaces on the inside, and any finish that could off-gas near nesting birds.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

A common two-story layout uses an upper and lower unit of roughly the same footprint, stacked and separated by a shared divider. Each unit should measure about 5 inches square on the inside floor, with a 1-1/4 inch entry hole for small cavity nesters such as wrens or chickadees. Adjust the hole size to suit the species you want to attract.

Cut List for a Basic Two-Story Box

Cut all parts from one board where possible to keep grain patterns consistent. The list below assumes 3/4 inch stock and produces one complete box.

  • Two side panels, 9 x 6-1/2 inches (front and back walls with a sloped roof cut later)
  • Two side walls, 5-1/2 x 9 inches, for the left and right sides
  • Two floors, 5 x 5 inches, one per compartment
  • One center divider, 5-1/2 x 5 inches, with no entry hole
  • Two roof panels, 6 x 7 inches, angled to shed rain
  • One front panel per unit, with entry holes drilled after assembly

Mark the roof angle on the top edges of the front and back panels before cutting. A 15 to 20 degree slope is typical and sheds water well.

Assemble the Two Compartments

Build the lower unit first, then the upper, and join them with the divider in the middle. Glue and nail or screw each joint, and drill pilot holes near board ends to prevent splitting.

  1. Attach each floor inside the walls so the floor sits 1/4 inch above the bottom edge. This gap lets water drain out.
  2. Drill four 1/4 inch drain holes in each floor.
  3. Assemble the four walls of the lower unit around its floor. Keep the corners square with a clamp and check with a combination square.
  4. Glue and fasten the center divider so it sits flush with the middle of the box.
  5. Build the upper unit the same way and fasten it on top of the divider.
  6. Attach the roof panels so they overhang the front by about 1 inch.
  7. Drill entry holes in the front panels after assembly, centered about 6 inches above each floor.

Mount and Maintain the Finished Box

Mount the box on a pole or the side of a tree at least 5 to 6 feet off the ground, facing away from prevailing winds. Keep the box out of direct afternoon sun. Clean out old nesting material once a year after the season ends, and check that the drain holes stay clear.

Common mistakes

  • Skipping drain holes, which lets rainwater pool on the floor and soak nesting material.
  • Using treated lumber or painted interiors that can harm nestlings.
  • Making the entry hole too large, which lets predators or competing species in.
  • Gluing the roof without leaving it removable for cleaning.
  • Cutting parts before confirming the divider height matches both units.
  • A 1-1/4 inch hole saw or spade bit set makes clean, accurate entry holes that stay round after drilling. View on Amazon
  • A combination square lets you check corners and roof angles quickly while assembling each unit. View on Amazon
  • Exterior wood glue and stainless steel exterior screws help the box hold up to weather and temperature swings. View on Amazon

If you want more ideas before starting, see Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists for other wood designs, or Simple Cedar Birdhouse Plans: A Step-by-Step Build in One Weekend for a single-chamber option. Builders interested in a specific species may also find Tree Swallow Birdhouse Plans: A Step-by-Step Build Guide useful for entry hole sizing.

FAQ

What size entry hole should a two-story birdhouse have?

A 1-1/4 inch hole suits many small cavity nesters such as wrens and chickadees. Larger species need bigger openings, so check the requirements for the birds you want to attract before drilling.

Can I use one large box for two families?

The divider keeps the two compartments separate, so each pair has its own space. Make sure the divider is solid and fastened well so neither side can open into the other.

How often should I clean a two-story birdhouse?

Clean it once a year after nesting season ends, removing old nest material and checking the drain holes. Do not clean during the active nesting period, since disturbing a nest can cause birds to abandon it.

Conclusion

A two-story box is a practical build that gives two bird pairs separate nesting space in a single structure. Measure carefully, leave drain holes in every floor, and size each entry hole for the species you hope to host. Follow the cut list and assembly order above, and you will have a sturdy nest box that lasts several seasons.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.