Updated November 2026

Six sided birdhouse plans give you a hexagon-shaped nest box that is easy to build from a few cedar or pine boards once you understand the geometry. This guide walks you through the layout, the cut list, the assembly order, and the hole sizing so you finish with a sturdy, weather-resistant house. Most builders can complete one in a single weekend.

Understand the Geometry Before You Cut

A regular hexagon has six equal sides and six interior angles of 120 degrees. For a birdhouse, the simplest approach is to build six identical walls, each with a 30-degree bevel on both long edges, so the walls meet at the correct angle when assembled. A quick check: if your walls are cut to a 30-degree miter on each edge, the finished ring will close cleanly around a six-sided floor.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

If you plan to add a roof, the top also needs six matching sides or a shallow pyramid cap. Plan the roof angle before you cut the walls so the top edges line up.

Cut List and Materials

Most six-sided designs use a nominal 1-inch thick board, often cedar or cypress, because these woods resist rot. Plan for a 6-inch wide board for walls and a separate piece for the floor and roof. A typical cut list looks like this:

Part Qty Dimensions
Wall panels 6 5-1/2 in. wide x 8 in. long, mitered 30 degrees on both long edges
Floor 1 6-sided, about 6 in. across flat to flat
Roof panels 2 or 6 Sized to your chosen roof style
Entrance hole 1 (cut) Hole diameter set by target species

Double-check every measurement against your own plan, because the mitered edges change the finished length slightly.

Assembly Steps for a Six-Sided Nest Box

  1. Cut all six wall panels with a 30-degree bevel on each long edge. Dry-fit them on a flat surface to confirm the ring closes without gaps.
  2. Drill pilot holes and attach the walls to each other with exterior wood glue and corrosion-resistant screws, working around the ring one pair at a time.
  3. Cut the hexagonal floor and attach it to the bottom of the wall ring. Drill two or three small drainage holes in the floor.
  4. Attach the roof panels, leaving the front panel slightly open for ventilation if your design calls for it.
  5. Drill the entrance hole on the front wall at the height specified for your target bird, then sand all edges and leave the exterior unfinished or apply a non-toxic exterior sealer.

Hole Size and Mounting Height

Entrance hole diameter determines which birds can use the house. Common sizes are around 1-1/8 inches for many small songbirds and larger for others. Mount the box 5 to 10 feet off the ground, facing away from prevailing winds and direct afternoon sun.

Tools You Will Need

  • Miter saw or table saw with a 30-degree blade setting
  • Drill and bits for pilot holes, drainage holes, and the entrance hole
  • Clamps to hold the ring while glue sets
  • Sandpaper, 120 grit or finer

A sliding compound miter saw makes the 30-degree bevels far more repeatable than a handheld saw, especially across six identical pieces. View on Amazon

Band clamps hold a six-sided ring square while the glue cures, which is hard to manage with standard bar clamps. View on Amazon

A hole-cutting bit set lets you drill clean entrance holes without splintering the face. View on Amazon

Common Mistakes to Avoid

  • Cutting the bevels on the wrong edge, which leaves the ring open at the seams.
  • Skipping the dry fit, then discovering a gap after the glue has set.
  • Using untreated pine outdoors, which warps and rots within a few seasons.
  • Drilling the entrance hole too large, which invites predators and competing species.
  • Forgetting drainage and ventilation, which leads to moisture buildup inside.

If you want to compare other nest box styles before committing, the guide Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists shows several beginner-friendly alternatives. For a simpler starter project, One-Board Birdhouse Plans Free: Build a Cedar House in One Afternoon uses far less material. Builders interested in a species-specific design can also look at Plans for a Bluebird Birdhouse: Build One in a Weekend or Wren Birdhouse Plans Free: Build a Cedar House in One Weekend.

FAQ

Do six sided birdhouses work for all birds?

No. The entrance hole size and interior space determine which species will use the box. Match the hole diameter and mounting height to the birds you want to attract.

What wood is best for a six-sided birdhouse?

Cedar, cypress, and rot-resistant pine are common choices because they hold up outdoors without chemical treatment. Avoid pressure-treated lumber for nest boxes that birds will occupy.

Is a six-sided birdhouse harder to build than a square one?

It takes more precise angle cuts, but the process is straightforward once you dry-fit the walls. Builders with a reliable miter saw usually find the extra step manageable.

Conclusion

Six sided birdhouse plans reward careful layout more than advanced joinery, so focus on accurate 30-degree bevels and a clean dry fit. With the right entrance hole and mounting height, your finished box can serve a range of small songbirds for years. Consult a local extension office or experienced builder if you have questions about regional species.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.