Updated November 2026

Free moose birdhouse plans give you a fun, character-filled project that works as a real nest box and a garden feature at the same time. In this guide, you will get the dimensions, a cut list, the assembly order, and the finishing details you need to build a moose-shaped house in a weekend with basic tools. The design uses standard lumber and simple joinery, so it suits a first-time builder as well as someone who has made a few boxes already.

What You Will Build

The moose birdhouse is a flat-sided box with a sculpted head and antlers cut from the front panel. The main body is a rectilinear nest chamber, while the moose head sits on top as a decorative profile. The entrance hole is placed on the body, not the head, so the nest chamber stays dry and protected. Because the profile is simple, you can cut it with a jigsaw and a few clean passes on a sander.

Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.

Finished dimensions are roughly 9 inches tall, 7 inches wide, and 8 inches deep, which makes this house a good fit for chickadees, nuthatches, wrens, and small titmice. If you want a larger house for bluebirds or a different species, adjust the entrance hole and floor depth as described in the sizing section below.

Materials and Tools Needed

Choose a stable, weather-resistant wood. Cedar, cypress, or pine treated for exterior use all work well. Avoid pressure-treated lumber that is labeled for ground contact, and never use painted or chemically treated scraps for the interior, since birds can be harmed by fumes and residues.

  • One 1×8 cedar or pine board, about 4 feet long, for the body, floor, and roof
  • One 1×6 board, about 2 feet long, for the moose head profile
  • Exterior wood glue and 1-1/4 inch exterior screws or galvanized finish nails
  • A table saw, miter saw, or circular saw with a straight guide
  • A jigsaw with a fine-tooth blade for the head profile
  • A drill with a 1-1/8 inch Forstner bit or hole saw for the entrance
  • A random orbit sander with 120- and 180-grit paper
  • A tape measure, combination square, and pencil
  • A exterior-grade, water-based stain or a bird-safe, unfinished wood surface

Cut List for the Moose Birdhouse

All dimensions below are finished sizes for 3/4-inch nominal lumber, which measures about 3/4 inch thick and 7-1/4 inches wide for a 1×8. Mark each part on the board before you cut, and label the pieces so you do not mix up the front and back.

Part Quantity Dimensions (inches) Material
Front panel (with moose head profile) 1 7-1/4 W x 9 H 1×8 cedar or pine
Back panel 1 7-1/4 W x 9 H 1×8 cedar or pine
Side panels 2 7-1/4 D x 7 H 1×8 cedar or pine
Floor 1 5-1/4 W x 7-1/4 D 1×8 cedar or pine
Roof 1 8 W x 8-1/2 D (cut to slope) 1×8 cedar or pine
Antler accents (optional) 2 1 W x 3 L 1×6 scrap

Sizing note: a 1-1/8 inch entrance suits chickadees and nuthatches, while 1-1/2 inches allows wrens and some titmice. Check your local species guide before you drill, because an oversized hole invites starlings and sparrows that will take over the nest.

Step-by-Step Build Instructions

Step 1: Cut the Panels to Size

Rip your 1×8 boards to a consistent width, then crosscut each part to length with a miter or circular saw. Check that the two side panels match exactly, since uneven sides will make the roof sit crooked. Keep the cut edges square and remove any splinters with light sanding.

Step 2: Lay Out and Cut the Moose Head

Draw the moose head profile on the front panel, starting from the top edge. Keep the antlers on the upper portion and the nose and jaw toward the bottom, where the entrance hole will sit below the head. Cut the outline with a jigsaw, moving slowly around tight curves. Sand the cut edges smooth with 120-grit paper so the profile looks finished and does not snag.

Step 3: Drill the Entrance Hole and Drainage

Center the entrance hole about 6 inches above the floor on the front panel, below the head shape so the moose head acts as a visual frame. Drill a 1/4 inch drainage hole in each bottom corner of the floor, and a few 1/4 inch ventilation holes near the top of the side panels. Drainage keeps the nest dry, and ventilation prevents overheating in summer.

Step 4: Assemble the Box

Apply a bead of exterior glue to the edges of the floor and sides. Set the floor between the two side panels, then attach the back panel with screws driven from the outside. Add the front panel last, leaving the top edge open for now. Drive screws about 1 inch from each edge to avoid splitting the wood. Check for square by measuring the diagonals; they should match within 1/16 inch.

Step 5: Build and Attach the Roof

Cut the roof board so it overhangs the front and sides by about 1/2 inch. Angle the back edge if you want the roof to slope toward the rear, which sheds rain away from the entrance. Attach the roof with two hinge screws along the back edge if you want easy access for cleaning, or fix it permanently with screws and glue for a simpler build.

Step 6: Finish the Surfaces

Sand all exterior faces to 180 grit, then wipe away dust. Leave the interior rough and unfinished so adult birds can cling to the walls. Apply a thin coat of exterior, water-based stain or a bird-safe clear finish to the outside, and let it dry fully before mounting. Avoid oil-based products with strong solvents inside the box.

Step 7: Mount the Birdhouse

Mount the house 5 to 10 feet off the ground on a post or tree, facing away from prevailing winds and direct afternoon sun. Use a smooth-sided pole or a metal predator guard to keep cats and raccoons away. Clean the box after each nesting season to prepare it for the next group.

Common Mistakes to Avoid

  • Skipping drainage holes, which lets water pool on the floor and chill the nest.
  • Using a hole that is too large, which lets starlings and sparrows move in.
  • Painting or staining the interior, which can release fumes and harm chicks.
  • Mounting the house in full sun all day, which can overheat young birds.
  • Driving screws too close to the edge, which splits the thin wood.
  • Forgetting to clean out old nesting material between seasons.

Tips for a Cleaner Build

Dry-fit every part before you apply glue. This lets you catch alignment problems while they are still easy to fix. Cut the moose profile on the front panel first, then use it as a template for matching the antler pieces if you choose to add them. Pre-drill screw holes in cedar, since it splits more easily than pine. If you want the house to last longer, seal the end grain on the roof and floor with a thin coat of exterior finish.

A fine-tooth jigsaw blade makes the moose head profile much cleaner than a coarse blade, which can tear the grain on softer woods. View on Amazon

A 1-1/8 inch Forstner bit drills a clean, flat-bottomed entrance hole without blowing out the back of the panel. View on Amazon

A random orbit sander speeds up smoothing the curved head profile and gives an even finish on the flat panels. View on Amazon

Exterior, water-based stain protects the outside of the house without leaving residues inside. View on Amazon

FAQ

Are these moose birdhouse plans really free?

Yes, the dimensions and build steps in this guide are free to use for personal projects. You only need to supply your own lumber and tools.

What wood is best for a moose birdhouse?

Cedar is a popular choice because it resists rot and does not need heavy finishing. Untreated pine also works if you seal the exterior well.

What size entrance hole should I use?

A 1-1/8 inch hole suits chickadees and nuthatches, while 1-1/2 inches fits wrens and some titmice. Choose the size based on the species you want to attract.

Can I paint the inside of the birdhouse?

It is best not to. Leave the interior unfinished so the wood is natural and breathable, and avoid any paint or stain that could release fumes near nestlings.

How high should I mount the birdhouse?

Most small songbird houses work well 5 to 10 feet off the ground. Check the species guide for your target bird, since some prefer higher or lower placements.

Do I need a predator guard?

A predator guard is strongly recommended. Cats, raccoons, and snakes can reach nests on poles or trees, and a smooth metal baffle or a slick-sided post reduces that risk.

When should I clean out the birdhouse?

Clean the box after each nesting season, removing old material and checking for parasites. Do not clean it during active nesting, since that can disturb birds that are still using it.

Conclusion

With these free moose birdhouse plans, you can build a sturdy, attractive nest box in a single weekend. Follow the cut list carefully, keep the interior unfinished, and size the entrance for the species you want to attract. Once it is mounted, a little seasonal cleaning will keep it useful for years.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.