Updated November 2026
Audubon birdhouse plans PDF documents give you a tested starting point for building a nest box that suits cavity-nesting songbirds. This guide explains what those plans typically specify, how to read a cut list, and how to build the box so birds will actually use it. You will finish with a sturdy, weather-resistant house and a clear idea of where to mount it.
What Audubon-Style Plans Usually Include
Most printable plans from conservation groups follow the same logic. The entry hole diameter is matched to a target species, the interior floor is measured to keep the nest above predators, and the box is sized so the nest cup fits comfortably. Before you cut anything, confirm which species the plan is designed for. A 1-1/2 inch hole suits a chickadee, while a 1-1/2 inch hole is far too large for a bluebird, which needs a 1-1/2 inch opening but a different interior depth than a wren house.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
Look for these details on any PDF:
- Interior floor dimensions and height from the floor to the entry hole
- Entry hole diameter and its distance from the top of the box
- A cut list with board lengths, widths and quantities
- Recommended wood thickness, usually 3/4 inch
- Drainage holes, ventilation gaps and mounting instructions
Step 1: Gather Materials and Read the Cut List
Use untreated softwood or cedar at 3/4 inch nominal thickness. Pine, cedar and cypress are common choices. Avoid pressure-treated lumber and painted or stained wood inside the box, since fumes and residues can harm nestlings. Check the cut list against your stock before cutting. Mark each piece with its part name, such as front, back, sides, floor and roof.
Step 2: Cut and Drill the Parts
Cut each piece to the length and width in the plan, using a table saw or circular saw with a guide. Square edges matter, because gaps let rain and drafts into the nest. Drill the entry hole using a hole saw or Forstner bit at the diameter the plan specifies, measured from the top of the box so the opening sits at the correct height. Drill drainage holes in the floor, about 1/4 inch in diameter, and add ventilation holes near the top of each side.
Cutting the Entry Hole Accurately
Clamp the front board before drilling to prevent tear-out on the back face. Drill slowly and ease off as the bit breaks through. If you use a hole saw, drill a pilot hole first so the saw stays centered.
Step 3: Assemble the Box
Join the sides to the floor and back with exterior-grade screws or galvanized nails, pre-drilling near the ends to avoid splitting. Attach the front panel last so you can clean out debris and check the interior. Leave the roof attached with hinges or a removable panel so you can clean the box between seasons. Add a sloped roof with a 1-inch overhang on the front to shed water away from the entry.
Step 4: Mount the Birdhouse Correctly
Placement affects occupancy as much as construction. Most cavity nesters do best with the entry hole facing away from prevailing winds and the box mounted on a pole or post, not a tree trunk where raccoons and cats can reach it. Mounting heights and distances vary by species, so check the plan’s instructions. Use a predator guard if squirrels or snakes are a problem in your area.
Common Mistakes
- Using a hole that is too large, which lets in starlings and house sparrows that compete for the nest
- Skipping drainage holes, which allows water to pool on the floor
- Painting or staining the interior, which can harm birds
- Mounting the box too close to feeders or in direct afternoon sun
- Cleaning the box in the middle of nesting season
Recommended Gear
A hole saw sized to the entry diameter gives you a clean, round opening without guesswork. View on Amazon
A Forstner bit set is useful for drilling flat-bottomed holes and clean drainage openings. View on Amazon
Exterior-grade wood screws resist rust and hold the joints tight through seasonal swelling. View on Amazon
FAQ
Are audubon birdhouse plans PDF files free to use?
Many conservation organizations publish their plans for free download for personal building. Check the document for any usage notes before sharing or selling builds.
What wood is safest for a birdhouse?
Untreated cedar, pine or cypress at 3/4 inch thickness is the usual recommendation. Avoid pressure-treated wood and paints or stains on the inside.
How high should I mount a birdhouse?
Height depends on the species the plan targets, so follow the mounting instructions in your PDF. Mount on a pole or post and add a predator guard where needed.
Conclusion
Audubon birdhouse plans PDF documents give you accurate hole sizes, floor heights and cut lists that match a specific species. Build with untreated wood, drill precisely and mount the box where predators cannot easily reach it. Following these steps gives you a birdhouse that is more likely to draw nesting birds year after year.
Related reading
- Free Birdhouse Plans PDF: 6 Printable Designs With Cut Lists
- Fence Picket Birdhouse Plans PDF: A Step-by-Step Build Guide
- Wren Birdhouse Plans Free: Build a Cedar House in One Weekend
- Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists
- Wine Cork Birdhouse Plans: A Step-by-Step Build for Beginners
- Western Bluebird Birdhouse Plans: Build a Nest Box in One Afternoon
