Updated November 2026

Dove birdhouse plans free of charge are easier to find than you might expect, but most of them are not really houses. Mourning doves don’t use enclosed nest boxes. They build loose platforms of twigs and grass, so the most useful plan is a flat, open shelf with a small rail or lip to hold the nest in place. This guide gives you a cut list, the steps to assemble it, and the placement details that keep a dove pair coming back.

What Doves Need From a Nesting Structure

Mourning doves nest in open shrubs and tree forks, usually six to fifteen feet off the ground. They want a level surface, some overhead cover from rain and predators, and a clear approach. A platform meets all three needs. Skip the walls and roof you would add for a bluebird box, because a closed box will be ignored.

Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.

Dove Platform Cut List and Materials

This design uses rough cedar or cypress, which resists rot without paint. Use a pressure-treated board only if it is rated for ground contact and you let it dry fully before building. Your cut list:

  • Platform floor: one piece 1 x 10 inches, 12 inches long
  • Front lip: one piece 1 x 2 inches, 12 inches long
  • Two side rails: 1 x 2 inches, 4 inches long each
  • Two support posts or mounting cleats: 1 x 3 inches, 8 inches long each
  • Exterior wood screws, 1¼ inch, plus wood glue

How to Assemble the Platform Step by Step

  1. Cut all pieces to the lengths above. Square the ends with a miter saw or a handsaw and a square.
  2. Lay the 1 x 10 floor flat. Center the front lip along one long edge, flush with the surface, and glue and screw it in place with two screws per end.
  3. Attach the side rails at each end of the floor, set back 1 inch from the front edge, to form a shallow cradle for the nest.
  4. Drill two pilot holes through the back edge of the floor for mounting. Pilot holes prevent splitting in cedar.
  5. Fasten the support cleats to the underside, centered, so the platform can be bolted or screwed to a post or fence.
  6. Sand the edges lightly and leave the wood unfinished. Do not use paint, stain or varnish on the nesting surface.

Drainage Holes

Drill four to six 1/4-inch holes in the floor. Rain that pools on the platform will rot the nest and soak eggs, so drainage matters more here than in any enclosed box.

Where and How to Mount the Platform

Mount the platform six to ten feet high on a post, a fence top or the crook of a tree limb. Face it away from prevailing winds and place it where a cat cannot easily reach it. Add a bit of loose twig or straw to the platform to encourage nesting. Once a pair settles in, leave the nest alone and avoid disturbing them during incubation, which runs about two weeks.

Feature Recommendation
Platform size About 10 x 12 inches
Mounting height 6 to 10 feet
Wood Cedar or cypress, unfinished
Drainage 4 to 6 holes, 1/4 inch

Common Mistakes to Avoid

  • Building an enclosed box with a roof and entrance hole, which doves will not use.
  • Painting or sealing the nesting surface, which can harm eggs and chicks.
  • Skipping drainage holes, leading to a soaked and failed nest.
  • Mounting too low, where ground predators and cats have easy access.
  • Checking the nest too often, which can cause the adults to abandon it.

A clean, accurate cut makes this platform sit flat, so a stable saw setup matters. A miter saw handles the square ends quickly. For the mounting holes and pilot holes, a cordless drill with a bit set keeps the work consistent.

  • A miter saw for square, repeatable cuts on the floor and lip pieces. View on Amazon
  • A cordless drill driver with a bit set for pilot holes and drainage holes. View on Amazon
  • Exterior wood glue and stainless or coated exterior screws to resist weather. View on Amazon

FAQ

Do mourning doves really use a platform instead of a box?

Yes. Mourning doves build open, flimsy nests on flat surfaces and rarely use enclosed boxes. A simple platform with a lip is the design they are most likely to accept.

What wood is best for a dove platform?

Unfinished cedar or cypress is a good choice because it resists rot without coatings. Avoid painted or chemically treated wood on any surface the birds will touch.

How high should I mount a dove platform?

Six to ten feet is a common range, placed where cats and ground predators cannot easily reach. Face it away from strong prevailing winds.

Conclusion

A flat cedar platform with a front lip and drainage holes is all a mourning dove needs. It takes an afternoon to build and can be mounted in minutes. Use the cut list above, leave the wood unfinished, and give the pair room to nest undisturbed.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.