Updated November 2026
Learning how to make a birdhouse plans is easier than most people expect. You decide the species you want to attract, work out the entry hole, floor size and interior height, then turn those numbers into a cut list you can take to the lumber rack. By the end, you will have a simple, written plan you can build from and reuse.
Start With the Species, Not the Design
Every bird has preferred dimensions, and those numbers drive the whole plan. A chickadee box, for example, uses a hole about 1 1/8 inches across and a floor near 4 by 4 inches. A bluebird box uses a 1 1/2 inch hole and a larger floor. Look up the target species before you sketch anything. If you want a starting point, Free Plans to Make a Birdhouse: 5 Easy Designs for Beginners shows how different sizes compare.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
Draw the Plan and Build the Cut List
Sketch the box on graph paper or in a free drawing app. Mark the front, back, two sides, roof, floor and any mounting panel. Write the length, width and thickness of each piece, then add the quantity. Use nominal 3/4 inch pine, cedar or cypress, and avoid pressure-treated lumber, since the chemicals can harm nesting birds. Your cut list should look something like this:
| Part | Quantity | Approximate size |
|---|---|---|
| Front | 1 | 5 3/4 in tall x 4 1/2 in wide |
| Back | 1 | 9 in tall x 4 1/2 in wide |
| Sides | 2 | 8 1/2 in tall x 4 1/2 in wide |
| Floor | 1 | 4 in x 4 in |
| Roof | 1 | 6 in x 6 in |
Treat these figures as a model for a small cavity-nester. Adjust them to match your species’ published requirements.
Cut, Drill and Assemble the Box
Cut and Drill
- Cut each board to the lengths on your cut list.
- Drill the entry hole in the front panel, positioned about 6 to 7 inches above the floor for most small species.
- Drill four to six 1/4 inch drainage holes in the floor and two ventilation holes near the top of the sides.
- Rough up the inside of the front panel, or cut shallow grooves, so fledglings can climb out.
Assemble
- Attach the floor to the sides and back with exterior screws or galvanized nails, leaving the front unattached for now.
- Attach the front panel last, so it can be removed for cleaning.
- Fasten the roof with hinges or screws, and leave a slight overhang on the front to shed rain.
Finish Safely
Leave the inside and the entry hole unfinished. Use an exterior, non-toxic finish on the outside only, and let it cure completely before mounting. Mount the box on a pole or fence post with a predator guard, away from feeders and high-traffic areas. For a more detailed build sequence, Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists walks through finishing and mounting options.
Recommended gear
A basic set of tools makes the build accurate and repeatable. A Forstner bit set gives clean entry holes without tear-out, and a combination square keeps your cuts square. A brass wood screw assortment resists rust better than steel and suits outdoor boxes. Search for these items: View on Amazon, View on Amazon, View on Amazon.
Common mistakes
- Using a hole that is too large, which lets predators or competing species in.
- Skipping drainage holes, which lets moisture build up and rot the floor.
- Painting or staining the inside, which can release fumes that harm chicks.
- Mounting the box in full sun, which can overheat the nest.
- Making the front fixed, so you cannot clean out old nesting material between seasons.
FAQ
What wood is best for a birdhouse?
Untreated cedar, cypress and pine are the most common choices. They resist weather reasonably well and do not contain chemicals that can harm birds.
How big should the entry hole be?
It depends on the species. Chickadees use about 1 1/8 inches, while bluebirds use about 1 1/2 inches. Check the requirements for the bird you want to attract.
When should I clean out a birdhouse?
Clean it after the nesting season ends, usually in late summer or fall, to remove old material and parasites. Avoid cleaning while birds are actively nesting.
Conclusion
Knowing how to make a birdhouse plans comes down to three steps: pick the species, set the dimensions, and write a clear cut list. Build a simple box first, then adjust the design as you learn what your local birds prefer. Your first build is the start of a plan you can refine for years.
