Updated November 2026
Six sided birdhouse plans give you a nest box with a roof that sheds rain well and a floor that stays dry. This guide walks you through a simple hexagonal design built from one 1×6 cedar board and a few screws, with a complete cut list and assembly order. You can finish the build in an afternoon with basic hand and power tools.
Understanding the Six Sided Design
A six sided birdhouse uses six equal walls that meet at 60-degree angles. Each wall is a trapezoid when the sides are angled, but many builders simplify the shape by using straight-cut walls that meet at the corners. The result is a compact box with more exterior surface than a square house, so it needs slightly more care in cutting and fastening. The payoff is a roof that sheds water evenly from every direction.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
Cut List and Materials
Use rough or planed cedar, pine, or cypress at 3/4 inch thickness. Avoid pressure-treated lumber, since the preservatives can harm birds. The plan below produces a house about 7 inches across and 10 inches tall.
| Part | Qty | Dimensions | Notes |
|---|---|---|---|
| Walls | 6 | 3/4 x 5-1/2 x 8 in. | Bevel both long edges at 30 degrees |
| Floor | 1 | 3/4 x 6 x 6 in. | Hexagon, cut to fit inside walls |
| Roof panels | 6 | 3/4 x 4 x 6 in. | Bevel to match wall angle |
| Front hole plate | 1 | 3/4 x 5-1/2 x 8 in. | Cut 1-1/4 in. entrance hole |
Build Steps for a Six Sided Birdhouse
Cut the Walls and Bevels
Set your table saw blade to 30 degrees and rip both long edges of each wall piece. Check each cut against the others with a dry fit before moving on. Small differences add up across six walls.
Assemble the Walls
Glue and clamp the walls in pairs, then join the pairs into a hexagonal ring. Drive one 1-1/4 inch exterior screw into each corner joint, pre-drilling to prevent splitting. Let the glue cure for at least an hour before handling the frame.
Attach the Floor and Roof
Fasten the floor inside the bottom edge of the ring, leaving a 1/4 inch gap at the front for drainage. Attach the six roof panels to the top edges, then add a small finial or leave the peak open for ventilation. Drill four 1/4 inch drainage holes in the floor.
Mount the Entrance and Finish
Fit the front hole plate with a 1-1/4 inch entrance and attach it with screws so it can be removed for cleaning. Sand all exterior edges, then apply an exterior stain or leave the wood bare. Do not paint the interior.
Common Mistakes
- Cutting bevels at the wrong angle, which leaves gaps at the corners.
- Skipping drainage holes, which lets moisture pool in the floor.
- Using treated lumber or interior paints that can release fumes.
- Mounting the box in full sun, which can overheat nestlings.
- Driving screws without pre-drilling, causing the cedar to split.
Recommended Gear
- A digital angle gauge helps you confirm the 30-degree bevel before ripping the walls. View on Amazon
- A countersink bit set keeps screw heads flush and prevents splitting at the corners. View on Amazon
- A clamp set for small glue-ups holds the hexagon square while the glue cures. View on Amazon
FAQ
What wood works best for six sided birdhouse plans?
Cedar is the most common choice because it resists rot and stays stable outdoors. Untreated pine or cypress also works if you seal the exterior.
What entrance size should I use?
A 1-1/4 inch entrance suits small cavity nesters such as wrens and chickadees. Check the species you want to attract before you drill.
Where should I hang the finished house?
Mount it 5 to 10 feet off the ground on a post or tree, facing away from prevailing winds and direct afternoon sun. Adjust height based on the species you hope to attract.
Conclusion
With a careful bevel cut and solid corner joints, these six sided birdhouse plans produce a durable nest box in a single afternoon. Pre-drilled screws, drainage holes, and an untreated finish will keep the house in good shape for many seasons. Browse the related plans on this site to try another design next.
