Updated November 2026
These purple finch birdhouse plans give you a simple, open-front-style nest box sized for the species, with a 6-inch-high interior, a shallow entry at the top, and a cut list you can size from a single cedar or pine board. You will finish with a box that is easy to clean, mounts safely, and suits a purple finch’s preference for an open or semi-open nesting site. The whole build takes a weekend with basic hand tools.
Know What the Purple Finch Needs Before You Cut
Purple finches are not cavity nesters in the strict sense. They usually build open cup nests in conifers, so a conventional closed box rarely attracts them. A nest shelf or a box with a large open front, placed in a dense evergreen or near a dense shrub, gives the best chance of a nesting pair. Many builders therefore choose a shelf-style box with a roof overhang rather than a traditional hole-entry house.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
Cut List and Dimensions for the Open-Front Box
Use 3/4-inch cedar or untreated pine, and cut all parts to the sizes below. Rough-cut slightly oversize, then trim to finished length on the table saw or with a miter saw.
| Part | Qty | Dimensions |
|---|---|---|
| Back panel | 1 | 7 in × 12 in |
| Sides | 2 | 6 in × 10 in (angle top edges to slope) |
| Floor | 1 | 5 1/2 in × 6 in |
| Roof | 1 | 8 in × 8 in |
| Front lip | 1 | 7 in × 2 in |
Cut the sides with a 15-degree bevel along the top edge so the roof sheds rain. Drill a few 1/4-inch drainage holes in the floor and cut a small notch in the floor at the front for water runoff.
Assemble the Box Step by Step
- Lay the back panel flat and attach the two sides with exterior wood glue and 1 1/4-inch galvanized or stainless exterior screws, flush at the back edge.
- Attach the floor between the sides, set back so the front lip sits about 1/4 inch proud of the floor.
- Fasten the front lip across the top of the open front, leaving the opening below it around 4 inches high.
- Center the roof so it overhangs the front by about 2 inches and back by 1 inch. Attach with screws driven from inside the box through the sides.
- Sand all edges, then apply a water-based exterior stain or leave the wood natural. Do not use paint or varnish on the inside.
Mounting and Placement
Mount the box 6 to 15 feet off the ground on a conifer branch or a sturdy post, facing away from prevailing winds. Position it where it gets morning sun and afternoon shade. Use a bracket that holds the box firmly without pinching the branch.
Common Mistakes to Avoid
- Building a closed box with a small round hole. Purple finches rarely use these.
- Skipping the roof overhang, which lets rain blow directly onto the nest.
- Using pressure-treated lumber, which can leach chemicals harmful to birds.
- Placing the box in full sun, which can overheat eggs and chicks.
- Cleaning out the nest during the breeding season. Clean only between nesting periods.
Recommended Gear
A sharp hand saw or miter saw makes clean, square cuts on the thin cedar stock, which keeps the joints tight.
A pocket hole jig speeds up assembly and hides fasteners, though the box works fine with plain exterior screws. View on Amazon
Exterior-rated wood glue gives the joints durability against weather swelling and shrinking. View on Amazon
FAQ
What size should purple finch birdhouse plans use?
Plans typically use an interior floor of about 5 1/2 by 6 inches and a height of around 6 inches for an open-front or shelf-style box. Stick to these proportions rather than oversized designs, which may not attract the birds.
Do purple finches use standard birdhouses?
Usually not. They prefer open cup nests in evergreens, so a closed box with a small entry hole is rarely used. An open-front box placed in dense foliage works far better.
When should I clean the nest box?
Clean the box after the nesting season ends, removing old nesting material and droppings. Avoid disturbing an active nest, and check local wildlife rules before doing any maintenance during breeding season.
Conclusion
With the cut list above and a simple open-front design, you can build a nest box that suits the purple finch’s natural habits. Mount it in a sheltered conifer, keep it out of full sun, and leave it alone during nesting. For more builds, see House Finch Birdhouse Plans: A Step-by-Step Guide With Cut List and Free Finch Birdhouse Plans: A Step-by-Step Build With Cut List.
