Updated November 2026
Free plans for a dovecote birdhouse give you everything needed to build a classic, pigeon-style nest box in a single weekend: dimensions, a cut list and assembly steps. This guide walks through the design, the materials and the construction order so you can finish with a sturdy house that holds up to rain and sun. Plan on a modest amount of scrap lumber and basic hand or power tools.
Dovecote Birdhouse Dimensions and Cut List
A standard dovecote design is a box about 10 inches wide, 10 inches deep and 12 inches tall, topped with a pitched roof and a small round or square entry hole. Build the house from 3/4-inch exterior-grade plywood or cedar boards so the walls stay stable through seasonal temperature changes. Use this cut list as your starting point:
Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.
- Two front and back panels: 10 x 12 inches
- Two side panels: 9 x 12 inches (sized to sit inside the front and back)
- One floor: 9 x 9 inches
- Two roof panels: 7 x 12 inches, cut at a 30-degree bevel along the top edge
- One optional ventilation board for the front gable, about 6 x 2 inches
Mark every piece with a pencil before cutting, and double-check the roof bevel against the side walls. A small error here creates gaps that let in rain.
How to Assemble a Dovecote Birdhouse Step by Step
Assembly goes fastest when you build the box first and the roof second. Work in this order so each step has a flat surface to clamp against.
- Drill a 1-1/2-inch entry hole in the front panel, centered about 8 inches above the bottom edge. Many nest-box guides recommend this size for small songbirds.
- Drill four to six 1/4-inch drainage holes in the floor and a few small ventilation holes near the top of the side panels.
- Apply exterior wood glue to the edges of the floor and side panels, then fasten them with 1-1/4-inch exterior screws or galvanized nails.
- Attach the front and back panels, keeping all edges flush. Check for square with a tape measure across the diagonals.
- Fix the roof panels with stainless or galvanized screws through the top of the walls, leaving a small overhang of about 1 inch on each side.
- Add a hinged or removable side panel or front access panel so you can clean the house after each nesting season.
Finishing and Mounting
Sand the exterior lightly, then leave the inside rough so birds can grip the walls. Apply a exterior-grade, non-toxic finish only to the outside, and let it cure fully before mounting. Mount the house on a post or wall at least 5 to 6 feet above the ground, facing away from prevailing winds.
Materials, Tools and Recommended Gear
Cedar and exterior plywood both resist rot well, and pine works if you seal it properly. A drill, a jigsaw or circular saw, a hole saw and a countersink bit cover most of the work.
| Item | Purpose |
|---|---|
| 3/4-inch exterior plywood or cedar | Walls, floor and roof |
| Exterior wood glue | Strengthens joints |
| 1-1/4-inch exterior screws | Secure assembly without splitting |
| 1-1/2-inch hole saw | Creates the entry hole |
Recommended Gear
A stable work surface makes square cuts easier, and a clamp keeps panels aligned while glue sets. A countersink bit prevents screw heads from splitting thin cedar.
- A cordless drill with a hole saw set makes clean entry holes in plywood and cedar. View on Amazon
- Bar clamps hold panels square while the glue cures. View on Amazon
- A countersink bit set keeps screw heads flush for a clean finish. View on Amazon
Common Mistakes to Avoid
- Skipping drainage holes, which lets water pool and rot the floor.
- Using untreated pine or interior plywood that swells and delaminates outdoors.
- Making the entry hole too large, which invites predators and larger birds.
- Painting or staining the inside, which can trap fumes and discourage nesting.
- Mounting the house in direct, all-day sun without shade or ventilation.
FAQ
What wood is best for a dovecote birdhouse?
Cedar and exterior-grade plywood are the most reliable choices because both resist moisture and warping. Avoid interior plywood or untreated pine left exposed to rain.
How big should the entry hole be?
A 1-1/2-inch hole suits many small songbirds, while pigeon-style houses are often built with a larger opening. Check the species you want to attract before drilling.
When should I clean out a birdhouse?
Clean the house after each nesting season, once birds have left and no active nests remain. Removing old material reduces parasites and prepares the box for the next year.
Conclusion
With these free plans for a dovecote birdhouse, you can build a durable nest box from basic materials in one weekend. Accurate cuts, drainage holes and a sensible mounting height make the biggest difference to how long it lasts. For more designs, see Free Plans to Build a Birdhouse: 5 Easy Designs With Cut Lists and Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists.
