Updated November 2026

Birdhouse planter plans free designs combine a functional nest box with a container for flowers or herbs, so one build gives you shelter for birds and color in the yard. This guide walks through how to choose a design, how to lay out the cuts, and how to assemble a planter birdhouse that stays dry and holds soil. By the end, you will have a working plan you can cut from a single cedar or pine board.

Choose a Design That Fits Your Space

Most planter birdhouses fall into two types. A hanging model suits a porch or fence, while a mounted planter box works best on a post or wall. Pick the type first, because it decides the weight you can support and how much soil the box will hold. Keep the nest chamber small, typically 4 by 4 inches of floor space for songbirds, and place the planter on top or along the front so the entrance stays clear.

Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.

Cut Your Parts to Size

Use cedar, redwood or untreated pine at 3/4-inch thickness. Plan your cuts so every piece comes from one or two boards, which keeps waste low. A typical hanging combo uses these parts:

  • Two sides: 8 inches tall by 7 inches wide, angled at the top to shed rain
  • Front and back: 9 inches by 7 inches, with a 1 1/8-inch entrance hole cut 6 inches above the floor in the front piece
  • Floor: 4 1/2 inches by 4 1/2 inches, with four 1/4-inch drain holes
  • Planter tray: 4 inches deep, built as an open-top box fitted to the roof line
  • Roof: two panels, each 8 inches by 6 inches, overhanging the front by 1 inch

Check every dimension against the plan you choose before you cut. A few millimeters of error on the entrance hole or floor will change how birds use the box.

Assemble the Nest Chamber and Planter

Build the nest chamber first. Glue and screw the sides to the floor, then add the front and back. Use exterior wood glue and two galvanized screws per joint, drilled with pilot holes to prevent splitting. Let the glue cure for at least an hour before fastening the roof.

Next, attach the planter tray to the top of the nest box so it sits level. Line the inside of the tray with a sheet of landscape fabric, which holds soil while letting water drain. Mount the finished unit with a 1/4-inch hanger bracket or two wall screws, and check that the entrance faces away from prevailing wind.

Finish and Hang the Birdhouse Planter

Seal the exterior with a water-based exterior stain or a single coat of linseed oil, and leave the interior bare so the wood stays natural. Do not paint the inside of the nest chamber. Fill the planter with a light potting mix, plant shallow-rooted flowers such as petunias or sweet alyssum, and water from the top so the soil stays moist but not soggy.

Mounting height and placement

Hang songbird houses 5 to 10 feet off the ground, and keep them away from feeders so predators do not travel straight to the nest. Position the entrance so the morning sun hits it and the afternoon heat stays off the roof.

Common Mistakes

  • Skipping drain holes, which leaves the soil waterlogged and rots the floor
  • Cutting the entrance too large, which lets in starlings and predators
  • Using treated lumber in the nest chamber, which can harm nesting birds
  • Overfilling the planter, which adds weight and strains the hanger
  • Painting the inside, which traps moisture and fumes
  • Exterior wood glue bonds the joints and resists moisture, which matters for a box that lives outdoors. View on Amazon
  • A stainless or galvanized screw assortment avoids rust stains on cedar and holds up better than plain steel. View on Amazon
  • A hole saw set makes clean, round entrance holes without splitting the front panel. View on Amazon

FAQ

What wood is best for a birdhouse planter?

Cedar and redwood resist rot without chemical treatment, which makes them safe for nesting birds. Untreated pine works too if you seal the exterior well.

Can I plant directly in the nest chamber?

No. Keep soil in the planter tray only, so the nest chamber stays dry and free of soil and moisture.

How often should I water the planter?

Check the soil every day in hot weather and water when the top inch feels dry. Good drainage prevents overwatering.

Conclusion

A birdhouse planter combines shelter and color in one build, and a clear cut list keeps the project manageable for a weekend. Choose a design that fits your space, assemble the nest chamber before the planter, and check the entrance size before mounting. Browse more plans on the site to find a style that suits your yard.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.