Updated November 2026
Free Cub Scout birdhouse plans give your den a practical woodworking project that most boys and girls can finish in a single afternoon with adult supervision. This guide covers a simple gable-roof design, a cut list you can take to the lumberyard, the assembly order, and the details that keep birds safe. By the end, you will have a sturdy nest box ready to mount.
Materials and Cut List
Use 3/4-inch cedar, pine or cypress boards. Untreated wood is essential, since chemical preservatives can harm birds. The design below uses one 1×6 board, about 4 feet long, plus a few screws and a small hinge or hook for the roof.
Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.
| Part | Qty | Dimensions |
|---|---|---|
| Front and back | 2 | 5-1/2 in. x 11 in. |
| Sides | 2 | 5-1/2 in. x 8 in. |
| Floor | 1 | 4-1/2 in. x 4-1/2 in. |
| Roof panels | 2 | 5-1/2 in. x 7 in. |
Cut the front piece with a 1-1/4 inch entrance hole placed 6 inches above the floor, centered side to side. Drill the hole before assembly, because it is much harder to center once the box is closed.
Step-by-Step Assembly
Cut and Drill the Parts
- Cut all pieces to the sizes in the table. Check each one against a square.
- Mark the entrance hole on the front and drill it with a spade or Forstner bit.
- Drill four 1/8-inch drainage holes in the floor and two small ventilation holes near the top of each side.
Build the Box
- Attach the floor between the two sides with exterior wood screws. Keep the floor flush with the bottom edge.
- Fasten the front and back to the sides. Pre-drill every screw to prevent splitting the cedar.
- Score the inside front panel below the hole with a few shallow lines so fledglings can climb out.
Add the Roof
Attach the two roof panels so they meet at a peak with a small overhang on each side. Fasten one panel with a hinge so the roof lifts for cleaning each season. Leave the other panel fixed.
Mounting and Placement
Mount the box 5 to 10 feet off the ground on a post or tree trunk, facing away from prevailing winds. Keep it away from feeders, since busy traffic can scare nesting birds. For a full look at how the same design scales across species, see Cub Scout Birdhouse Plans: A Step-by-Step Build for Den Projects and Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists.
Common Mistakes to Avoid
- Using pressure-treated or painted wood, which can release harmful chemicals.
- Making the entrance hole too large, which lets predators such as starlings or squirrels in.
- Skipping drainage holes, which lets moisture collect and rot the floor.
- Nailing the roof permanently, so cleaning out old nests becomes impossible.
- Choosing a hole size without checking the target species. A 1-1/4 inch hole suits chickadees and wrens; smaller birds need smaller openings.
Recommended Gear
- Forstner drill bit set: clean, flat-bottomed holes make the entrance edge smooth and safe for birds. View on Amazon
- Exterior wood screws: galvanized or stainless screws resist rust and hold up outdoors. View on Amazon
- Combination square: accurate square lines keep the box from racking when screwed together. View on Amazon
FAQ
What wood is best for free Cub Scout birdhouse plans?
Cedar is the most common choice because it resists rot and does not need paint or stain. Pine and cypress also work if they are untreated.
Should the birdhouse be painted?
No. Leave the inside and outside unfinished, or use a non-toxic exterior finish only on the outside and let it cure fully before mounting.
When should we clean out an old birdhouse?
Clean it once each fall after the nesting season ends. Remove old nesting material and scrub the floor, then let it dry before the next spring.
Conclusion
With a good cut list and careful drilling, these free Cub Scout birdhouse plans make a satisfying first project for a den. Build it together, mount it in a quiet spot, and check it through the season. The birds will do the rest.
