Updated November 2026
Multi bird birdhouse plans describe a single structure with several separate nesting compartments, usually built from one board set and mounted on a single post. Following a good plan, you will end up with a box that houses two to six pairs of birds, each in its own sealed chamber with its own entrance. This guide walks through the design choices, the build steps and the mistakes that cause trouble later.
Choose a Design and Match It to Your Birds
Most multi-unit plans fall into two types: a stacked tower with a shared roof, or a flat cluster of side-by-side cells. Stacked designs take up less ground and suit a single post, while cluster designs give each compartment more separation. Before you cut anything, decide which species you want to attract, because entrance size controls who moves in. A 1-1/8 inch hole suits bluebirds and chickadees, while a 1-1/2 inch hole is typically used for tree swallows and some wrens. Smaller holes keep out starlings and house sparrows, which often crowd out native birds.
If you are still deciding between layouts, compare the options in Multi Room Birdhouse Plans: 4 Best Guides for Building Them (2026) and 3 Best Multi Unit Birdhouse Plans for Building Colonies (2026). Both show how different compartment counts change the overall footprint.
Prepare the Lumber and Cut List
Use untreated cedar, pine or cypress at 3/4 inch nominal thickness. Cedar resists rot and is a common recommendation for nest boxes. Avoid pressure-treated wood, paint with lead-based products, and any chemical treatment that could reach the nest. Before cutting, lay out every part, label it and check the plan’s dimensions against your actual board width.
- Cut the front, back and side panels to the height and width shown in your plan.
- Cut the floor pieces for each compartment, and drill drainage holes of about 1/4 inch in each floor.
- Cut the dividers between compartments to match the interior depth.
- Cut the roof panels with a slight overhang at the front, roughly 2 inches, to shed rain away from the entrances.
- Rough-cut the entrance holes in the front panels, then drill to final size using a Forstner bit or a hole saw.
Assemble the Compartments
Assemble each compartment as its own sealed box before joining them. Glue and screw the floor, back and sides, then fit the divider so it sits flush against the interior walls. Use exterior wood glue on every joint and drive corrosion-resistant screws or galvanized nails through the outside faces. Leave the front panel off until the internal dividers are secure.
Once each unit is built, join the compartments with screws through the dividers and check that no unit rocks or twists. Add the roof last, attaching it with hinges or screws so you can open the box for cleaning each fall. A hinged roof or side panel makes annual cleanout far easier and is a feature many multi-unit plans include.
Mount the House Safely
Mount the finished box on a 1-1/2 inch galvanized pipe or a 4×4 post set at least 5 feet off the ground. Place it in a spot with morning sun and some afternoon shade, facing away from prevailing winds. Keep it at least 30 feet from dense brush, since predators such as cats and snakes use cover to approach. Predator guards, such as a stovepipe baffle, help protect the nests from climbing animals.
Common Mistakes
- Making all entrance holes the same size, which lets unwanted species into every compartment.
- Omitting floor drainage holes, which leaves nests wet after heavy rain.
- Using pressure-treated or painted wood inside any compartment.
- Skipping the annual cleanout, which allows parasites to build up between seasons.
- Mounting the house in full sun or too close to thick shrubs.
Recommended Gear
- Forstner bit set: produces clean, flat-bottomed entrance holes without splintering the front panel. View on Amazon
- Exterior wood glue: bonds the dividers and seams so compartments stay sealed through weather changes. View on Amazon
- Galvanized deck screws: resist rust outdoors and hold the joints without splitting cedar. View on Amazon
FAQ
How many compartments should a multi bird house have?
Most plans use two to six compartments. More units attract more pairs but need more space, more material and more frequent cleaning.
Can one multi-unit house attract different bird species?
Yes, if each compartment has an entrance sized for its target species. Bluebirds and chickadees, for example, can share a structure with differently sized openings.
When should I clean out the nest boxes?
Clean them after the nesting season ends, typically in late summer or early fall, to remove old nesting material and parasites before the next year.
Conclusion
Good multi bird birdhouse plans give each compartment its own sealed chamber, a correctly sized entrance and proper drainage. Match your entrance holes to the birds you want, use untreated wood, and mount the house in an open, predator-aware spot. With those basics in place, a single build can support several bird families every season.
