Updated November 2026

Hanging wren birdhouse plans give you a small, simple nest box that house wrens and Carolina wrens will readily use. In this guide you will get a complete cut list, the dimensions that matter most, and the assembly steps for a box you can finish in an afternoon. Most of the work is straight cuts and a few screws, so it suits a first project.

Cut List and Materials

Use 3/4-inch cedar, pine or cypress with no treatment or finish on the inside. Rough-sawn stock is fine. Cedar resists rot and holds up outdoors without paint, which wrens prefer to a glossy surface. Cut the following pieces:

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • Front: 1 piece, 4 inches wide by 9 inches long, with the entrance hole drilled later
  • Back: 1 piece, 4 inches wide by 10 inches long (extends above the roof for mounting)
  • Sides: 2 pieces, 4 inches wide by 7 inches long, with the front edge angled to match the roof slope
  • Floor: 1 piece, 4 inches by 4 inches
  • Roof: 1 piece, 5 inches by 6 inches, overhanging the front and sides by about 1/2 inch

Add a few 1-1/4-inch exterior screws or galvanized nails, and wood glue if you want extra strength.

Drill the Entrance and Drainage Holes

Mark the entrance hole on the front panel, centered about 6 inches up from the bottom. Drill a 1-1/8-inch hole with a spade or Forstner bit. This size keeps out larger birds such as sparrows and starlings while letting wrens in. Use a sanding block to remove any splinters from the hole edge.

Drill four 1/4-inch drainage holes in the floor, one in each corner. Rain and condensation need somewhere to go, and wet nesting material is a common cause of failed broods.

Assemble the Box

  1. Attach the floor between the two side panels, flush at the bottom edge. Drive two screws through each side into the floor.
  2. Attach the front and back panels to the sides and floor. Keep the back panel flush with the rear edges so the roof sits level.
  3. Check that the box is square by measuring the diagonals. They should match within 1/8 inch.
  4. Center the roof over the top and fasten it with screws through the back panel. Leave the roof removable, or use a hinge on one side, so you can clean the box between seasons.

Roughen the inside walls with a few shallow scratches, or leave the rough-sawn texture. Wrens need to climb out, and smooth walls can trap fledglings.

Hang the Birdhouse Safely

Mount the box 5 to 10 feet off the ground on a post, fence line or tree trunk. Face the entrance away from prevailing winds and direct afternoon sun. Hang it in a shaded spot near shrubs or brush, since wrens like cover close to the nest. Avoid mounting it where cats can reach it, and keep it at least 20 feet from heavy feeder traffic.

Use a wire or a bracket rather than a nail through the box, so you can remove the box without damaging it. Check the mounting once a year for loose fasteners.

A sharp hand saw or miter saw makes the straight cuts clean enough for the roof and sides to fit well. View on Amazon produces a clean, round entrance hole without tearing the grain.

A random-orbit sander with 120-grit paper smooths the outside edges and removes splinters around the entrance. View on Amazon saves time on the front panel.

Common Mistakes

  • Using treated lumber, which can harm nesting birds.
  • Drilling an entrance hole larger than 1-1/4 inches, which lets in competing birds.
  • Skipping drainage holes, which lets the floor stay damp.
  • Leaving the interior painted or varnished, which can release fumes.
  • Hanging the box in full sun, which can overheat eggs and chicks.

For more builds in this style, see Wren Birdhouse Plans Free: Build a Cedar House in One Weekend and House Wren Birdhouse Plans: A Step-by-Step Build With Cut List. If you want a different species, Carolina Wren Birdhouse Plans: A Step-by-Step Build Guide covers a slightly larger box, and Simple Cedar Birdhouse Plans: A Step-by-Step Build in One Weekend offers another cedar option.

FAQ

What size entrance hole do wrens need?

A 1-1/8-inch hole suits house wrens and Carolina wrens well. It is small enough to keep out starlings and sparrows.

What wood is best for a wren house?

Untreated cedar is a common choice because it resists rot without paint. Pine or cypress also work if they are unfinished on the inside.

How high should I hang a wren birdhouse?

Mount it 5 to 10 feet off the ground in a shaded spot with nearby cover. Keep it away from heavy feeder traffic and cat access.

Conclusion

With cedar, a 1-1/8-inch entrance and a few screws, you can build a wren house that fits the species well. Cut the pieces accurately, add drainage, and hang the box in shade. Check it each season and clean it out after nesting ends.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.