Updated November 2026

Side mounted birdhouse plans describe a nest box with a rear or side cleat instead of a bottom-mounted pole. You build a simple box, attach a cleat to the back, and screw it to a fence post, tree trunk or wall. This guide gives you the dimensions, cut list and assembly order for a cedar box that suits small cavity nesters like chickadees and wrens.

Choose the Right Dimensions for Your Birds

Entrance hole size decides which species will use the box, so start there before you cut anything. A 1-1/8 inch hole fits chickadees and titmice, while a 1-1/4 inch hole suits bluebirds. Keep the floor at about 4 by 4 inches for small birds and the interior height between 6 and 8 inches so the nest sits well below the hole.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

Cedar, cypress and untreated pine all work well because they resist rot and do not need paint inside. Use 3/4-inch stock for the walls and floor, since thinner boards crack when screwed.

Cut List and Materials

Part Quantity Dimensions (inches)
Front panel 1 3/4 x 5-1/2 x 10
Back panel 1 3/4 x 5-1/2 x 12
Side panels 2 3/4 x 5 x 8-1/2
Floor 1 3/4 x 4 x 4
Roof 1 3/4 x 6 x 6
Mounting cleat 1 3/4 x 2 x 10

The back panel runs longer than the front so the roof overhangs the entrance and keeps rain out. Cut the entrance hole in the front panel 6 inches from the bottom after you have assembled the box.

Assemble the Box Step by Step

  1. Drill pilot holes and screw the floor between the two side panels, leaving the edges flush.
  2. Attach the back panel to the sides and floor, keeping the top edges even.
  3. Screw the front panel on last. Leave the front unscrewed at the top if you want easy access for cleaning.
  4. Drill 1/4-inch drainage holes in each bottom corner and a few ventilation holes near the top of the side panels.
  5. Center the roof, which should overhang the front by about 1 inch, and fasten it with screws.
  6. Drill the entrance hole with a Forstner bit or hole saw at the size your target species needs.

Attach the Side Mount Cleat

The cleat is what makes this design a side mounted build. Screw the 2-inch-wide cleat to the back of the box so it sits flush with the top edge and extends below the floor. Use exterior screws, and drive two into the post or fence board through the cleat. Mount the box at 5 to 10 feet high, with the entrance facing away from prevailing winds and away from direct afternoon sun.

Common Mistakes

  • Skipping drainage holes, which lets moisture collect in the floor and rot the box from the inside.
  • Using treated lumber, since preservative chemicals can harm nesting birds.
  • Mounting the box where cats or raccoons can reach the entrance.
  • Placing the entrance hole too close to the top, which makes the box harder to clean and lets predators reach in.
  • Painting the interior, which can trap fumes and heat.
  • Forstner bit set makes clean entrance holes without splintering the front panel. View on Amazon
  • Exterior wood screws hold up to weather and will not rust. View on Amazon
  • Cordless drill driver speeds up pilot holes and driving screws. View on Amazon

If you are new to cutting and assembly, the Simple Cedar Birdhouse Plans: A Step-by-Step Build in One Weekend design uses similar joinery. For a smaller species, compare the Wren Birdhouse Plans Free: Build a Cedar House in One Weekend layout.

FAQ

What wood is best for a side mounted birdhouse?

Cedar and cypress are the most common choices because they resist rot without chemical treatment. Untreated pine also works if you seal only the exterior.

How high should I mount the box?

Most small cavity nesters do well between 5 and 10 feet high. Choose a spot shaded from the hottest afternoon sun.

Can I use these plans for bluebirds?

Yes, with a 1-1/2 inch entrance hole and a slightly deeper interior. Bluebirds prefer open fields with scattered trees, so place the box accordingly.

Conclusion

A side mounted box is quick to build and easy to hang on a fence or post. Follow the cut list, choose an entrance size for your target species, and mount the house where predators cannot reach it. Clean it once a year after nesting season to keep the next occupants healthy.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.