Updated November 2026
Chestnut backed chickadee birdhouse plans give you a small, well-ventilated nest box sized for these tiny cavity nesters, which typically use holes around 1-1/8 inches across. This guide walks you through a simple box you can build from one 1×6 cedar board in an afternoon, with a cut list, assembly steps, and the details that keep the nest dry and predator-resistant.
Dimensions and Cut List for a Chestnut Backed Chickadee Box
Chestnut-backed chickadees are small, and they do well in a box with a floor of about 4 x 4 inches and an interior height of roughly 8 to 9 inches. Build from 3/4-inch cedar or another rot-resistant softwood, and keep all interior surfaces unfinished so the birds can grip them.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
- (2) Front and back panels: 3/4 x 5-1/2 x 9 inches
- (2) Side panels: 3/4 x 4-1/2 x 9 inches (sized to fit inside the front and back, or cut to sit between them, as you prefer)
- (1) Floor: 3/4 x 4 x 4 inches
- (1) Roof: 3/4 x 6 x 7 inches, with a slight overhang on all sides
Step-by-Step Assembly
- Cut all pieces to the sizes above. Square the ends with a miter saw or a table saw sled so the walls meet flush.
- Drill the entrance hole in the front panel, about 6 inches up from the floor, centered side to side. Use a 1-1/8 inch hole saw or Forstner bit. Clean any splinters from the inside edge.
- Drill drainage holes in the floor, four 1/4-inch holes at the corners, and ventilation holes near the top of each side panel.
- Assemble the box with exterior-grade wood glue and galvanized 1-1/4 inch exterior screws. Pre-drill every screw to prevent splitting. Keep the front and back panels overlapping the sides so the walls stay square.
- Attach the floor so it sits slightly recessed, which lets water drain out instead of pooling.
- Add the roof with hinges or a single screw on one side so you can open it for cleaning. Leave a small gap for ventilation under the roof edge.
Mounting and Placement
Mount the box 4 to 6 feet off the ground on a tree trunk or fence post, facing away from prevailing winds and afternoon sun. Chickadees often nest in mixed woodland, so a spot near conifers or trees with dead snags is ideal. Avoid placing the box near bird feeders, which can attract predators and crowd nesting territory.
Common Mistakes
- Using treated lumber or painted interiors, which can harm nesting birds.
- Making the entrance hole too large, which lets in predators and starlings.
- Skipping the floor drainage holes, which traps moisture and encourages mold.
- Mounting the box too low, where cats and raccoons can reach it.
- Failing to clean the box after each season to prevent parasite buildup.
Recommended Gear
- Forstner bit set makes clean, accurate 1-1/8 inch entrance holes without tearout. View on Amazon
- Galvanized exterior wood screws resist rust and hold up to outdoor weather. View on Amazon
- Exterior wood glue keeps joints tight when exposed to rain and temperature swings. View on Amazon
FAQ
What entrance hole size should I use for chestnut backed chickadees?
A hole of about 1-1/8 inches works well for chickadees while keeping larger birds out. Measure your bit before drilling, since hole saws vary slightly.
Can I use pine instead of cedar?
Yes, but use untreated pine and expect it to weather faster. Cedar resists rot better and holds up longer outdoors.
When should I clean the box?
Clean it once after the nesting season ends, removing old nest material and scrubbing the interior with hot water. Do not use chemical cleaners.
Conclusion
With a 4 x 4 inch floor, a 1-1/8 inch entrance, and proper drainage, this box gives chestnut backed chickadees a safe, dry place to raise their young. Build it from untreated cedar, mount it at a safe height, and check it each season. For more designs suited to small cavity nesters, browse our Birdhouse Plans for Chickadees: A Step-by-Step Guide for Beginners and Black Capped Chickadee Birdhouse Plans: A Step-by-Step Build Guide.
