Updated November 2026

Woodworking plans for nightstands give you everything you need to build a sturdy bedside table: dimensions, a cut list, joinery choices and a build sequence. This guide walks through how to read a nightstand plan, size it to your bed, cut and assemble the parts, and finish it so it holds up to daily use. Most beginners can complete a basic box-style nightstand in a weekend with a few hand and power tools.

Choose a Plan and Size It to Your Bed

Before cutting anything, confirm the nightstand height against your mattress. A common target is a top surface roughly level with the mattress top, which usually lands between 24 and 28 inches. Check the plan’s overall width, depth and drawer count, then adjust if your room or bed frame calls for something different. Write your final dimensions on a sketch so every later measurement traces back to one source.

Shopping for one? See our guide: 7 Best Fixed Base Wood Routers for Woodworking in 2026.

Build a cut list from the plan before buying lumber. Group parts by thickness (sides, top, bottom, back, drawer parts) and add about 10 percent extra stock for mistakes and grain matching. If you are new to measuring, review the basics in Woodworking Measuring Tools: Rules, Tapes and Squares.

Cut and Prepare the Parts

Dimension your stock to final thickness first, then cut parts to length and width. Set your table saw fence carefully and cut a test piece before running the full set. Label each part on its face and edge so you do not mix up left and right sides. Sand or plane the inside faces before assembly, because they are hard to reach afterward.

If your saw work feels unfamiliar, read Woodworking Power Tools: What Each Does and Safety Basics and Woodworking Safety Basics: The Hazards and Controls before you start.

Join the Carcass and Add Drawers

The carcass is the box made from the sides, top, bottom and back. Simple butt joints with glue and screws are acceptable for a first build, but dadoes, rabbets or pocket screws give more glue surface and better alignment. Dry-fit everything, check that the diagonals match, then glue and clamp. Let the glue cure fully before you remove the clamps.

For drawers, cut a shallow groove in the drawer sides to receive a thin bottom panel, and make sure the drawer opening is slightly larger than the drawer box to allow for seasonal wood movement. Test-fit each drawer and sand the fronts only as much as needed for a smooth, even gap of roughly 1/16 inch.

  1. Dimension stock and label all parts.
  2. Cut parts to the cut list and check squareness.
  3. Dry-fit the carcass, then glue and clamp.
  4. Install the back panel to square the case.
  5. Build and fit drawers, then add hardware.
  6. Sand progressively, then apply finish.

Finish and Install Hardware

Sand through a progression of grits, usually 120, 150 and 180, and remove all dust before finishing. Test your stain or oil on a scrap from the same board. Apply two to three thin coats of finish, sanding lightly between coats. Install drawer slides or wooden runners and pulls last, after the finish has cured.

Common Mistakes

  • Skipping the dry fit, which hides out-of-square assemblies until glue is set.
  • Building drawer openings too tight, causing sticking in humid weather.
  • Leaving the back panel off, which lets the case rack and twist.
  • Sanding too coarse too soon, leaving scratches that show under finish.
  • Cutting parts before checking the cut list twice.

A reliable square is essential for checking the carcass as you assemble it: View on Amazon.

Bar or pipe clamps hold the case together while glue cures, and you will need several: View on Amazon.

A random orbit sander speeds up flat sanding on large panels and leaves fewer swirl marks than hand sanding: View on Amazon.

FAQ

What is the best wood for a nightstand?

Poplar and pine are easy to work and affordable, while oak, maple and walnut are harder but more durable. Choose a species that matches your finish and the look you want.

How long does a nightstand take to build?

A basic box-style nightstand with one or two drawers often takes a full weekend, including finishing time. Allow extra days for glue and finish to cure.

Do I need a table saw to build nightstand plans?

No. A circular saw with a guide, a hand saw and a sanding block can produce acceptable parts. A table saw makes square, consistent cuts easier, but it is not required.

Conclusion

Woodworking plans for nightstands are most useful when you size them to your bed, build an accurate cut list and dry-fit before gluing. Follow the build sequence, check squareness at each stage and allow glue and finish to cure fully. With careful work, you will end up with a bedside table that is solid, square and built to last.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.