Updated November 2026
Woodworking guitar stand plans give you a clear path to a stable, good-looking stand that holds your instrument safely without scratching the finish. This guide walks through a simple A-frame design you can build in a weekend with basic tools. You will get a cut list, joinery steps and tips for protecting your guitar.
Choose a Design and Gather Your Materials
An A-frame stand is the easiest design for a beginner. Two angled legs meet at a top crossbar, and a cradle sits on the crossbar to hold the neck. Hardwoods like maple, poplar or walnut work well, and 3/4-inch stock gives enough strength for an acoustic or electric guitar.
Shopping for one? See our guide: 7 Best Fixed Base Wood Routers for Woodworking in 2026.
Cut List for a Basic A-Frame
- Two legs: 3/4″ x 3″ x 24″ (cut 15-degree angles at the top and bottom)
- One top crossbar: 3/4″ x 2″ x 12″
- One cradle base: 3/4″ x 3″ x 8″
- Two cradle arms: 3/4″ x 2″ x 6″
- Two foot braces: 3/4″ x 1.5″ x 10″
Before you cut, confirm dimensions against your largest guitar. A dreadnought needs a wider cradle than a parlor or electric body. Cut extra stock so you can adjust the fit.
Cut and Join the Frame
Mark all angles with a square and a bevel gauge, then cut the legs on a miter saw or with a hand saw. Check each leg against the others so the stand sits flat. Measuring tools like a combination square and a tape rule keep your joints accurate.
- Dry-fit the legs to the crossbar and adjust the angles until the frame sits square.
- Drill pocket holes or cut shallow half-lap joints where the legs meet the crossbar.
- Apply wood glue to each joint, clamp the frame and check for square with diagonal measurements.
- Let the glue cure for the time the manufacturer specifies, usually several hours.
For more on dependable joinery, see Woodworking Techniques: Measure, Cut, Join, Sand, Finish and Woodworking Clamps and Glue-Ups: Pressure and Prep.
Shape the Cradle and Add Protection
The cradle holds the guitar’s neck and body. Cut the cradle arms with a shallow curve so they hug the neck without pinching it. Sand the edges smooth, then glue a strip of felt or cork to each contact point. This keeps the finish safe and prevents slipping.
Round over all edges with a router or hand sander. A 1/8-inch roundover is enough to remove sharp corners without weakening the wood. For router setup and safe use, review Woodworking Power Tools: What Each Does and Safety Basics.
Finish the Stand
Sand progressively from 120 to 220 grit, wiping away dust between grits. Apply a finish such as a penetrating oil, wipe-on polyurethane or a water-based topcoat. Allow each coat to dry fully and lightly sand between coats for a smooth surface. Keep finish off the cradle pads so they still grip the guitar.
Common Mistakes
- Cutting legs at the wrong angle, which makes the stand wobble.
- Gluing joints without checking for square first.
- Using a cradle that is too tight and stressing the neck.
- Skipping felt or cork pads, which can scratch the finish.
- Finishing before the glue and wood have fully dried.
Recommended gear
A reliable combination square helps you check angles and square joints accurately. View on Amazon
Bar clamps hold the frame steady while glue cures. View on Amazon
Self-adhesive felt pads protect the guitar finish at each contact point. View on Amazon
FAQ
What wood is best for a guitar stand?
Hardwoods such as maple, poplar or walnut are strong and stable. Avoid soft, warping lumber for the legs and cradle.
Can a beginner build these woodworking guitar stand plans?
Yes. The A-frame design uses straight cuts, basic joinery and simple finishing, so it suits a first project.
How do I keep my guitar from getting scratched on the stand?
Cover every contact point with felt or cork, and keep finish off those surfaces so the pads grip properly.
Conclusion
With these woodworking guitar stand plans, you can build a sturdy A-frame stand that protects your instrument. Take time on the angles and joints, and the stand will hold steady for years. Check your dimensions against your guitar before you cut.
