Updated November 2026

Woodworking planter box plans give you a clear path from rough lumber to a sturdy outdoor planter that holds soil and drains properly. This guide walks through a simple 24-inch by 10-inch by 10-inch box made from cedar or pressure-treated lumber, with a cut list, assembly order and the details that keep the box from rotting in its first wet season.

Materials and Cut List for Planter Box Woodworking Plans

This design uses 1×6 boards (actual thickness about ¾ inch) for the sides and ends, plus a bottom of 1×4 or 1×6 slats with gaps between them for drainage. Cedar is the usual choice because it resists decay without chemical treatment, though many builders use ground-contact-rated pressure-treated lumber if they plan to line the box.

Shopping for one? See our guide: 7 Best Fixed Base Wood Routers for Woodworking in 2026.

  • Two long sides: 24 in. × 5½ in., ¾ in. thick (4 pieces if you want a double-high box; 2 pieces for the basic version)
  • Two end pieces: 10 in. × 5½ in., ¾ in. thick (2 pieces)
  • Bottom slats: 22 in. long, 1×4 stock, 4 to 5 pieces spaced ¼ in. apart
  • Corner posts: 1½ in. square, 10 in. long (4 pieces) for reinforcement, optional
  • Exterior-rated screws, 2½ in. long, and waterproof wood glue

How to Assemble the Box

  1. Cut all boards to length and label the inside faces. Check that the two ends match each other within about ⅛ inch.
  2. Drill pilot holes at each joint. Pre-drilling prevents cedar from splitting near the ends.
  3. Glue and screw the end pieces between the long sides. Keep corners square by measuring diagonals; they should match within ⅛ inch.
  4. Attach the corner posts inside the joints if you want extra strength, using two screws per joint.
  5. Fasten the bottom slats across the base, leaving ¼ inch gaps for drainage. Keep the slats perpendicular to the long sides so water runs out evenly.

Joinery and Finish Options

Butt joints with screws and glue are enough for a planter box, but a simple rabbet on each corner adds glue surface and hides end grain. A router with a rabbeting bit or a table saw with a dado set makes this quick. For more on setting up these cuts, see the Simple Birdhouse Woodworking Plans: A Step-by-Step Build for Beginners guide, which covers the same basic box construction.

For finishing, apply two coats of an exterior penetrating oil or water-based exterior stain to all surfaces, including the inside. Let it cure fully before planting. Avoid painting the inside, since trapped moisture accelerates rot at the base.

Common Mistakes With Planter Box Plans

  • Skipping drainage gaps. Solid bottoms trap water and rot the boards from below.
  • Using interior-grade screws. Standard steel screws rust and stain cedar; use stainless or exterior-coated fasteners.
  • Making the box too shallow. Less than 8 inches of soil dries out fast in summer.
  • Skipping a raised base. Set the box on blocks or feet so air circulates underneath.
  • Exterior waterproof wood glue: adds a moisture-resistant bond at every joint, which matters more than screws alone outdoors. View on Amazon
  • Stainless steel exterior deck screws: resist rust and staining on cedar, so the box keeps its look for years. View on Amazon
  • Penetrating exterior wood oil: soaks into the grain and slows moisture uptake from the outside. View on Amazon

FAQ

What wood is best for planter box woodworking plans?

Cedar and redwood resist decay naturally and are the most common choices. Ground-contact-rated pressure-treated lumber also works well, though many gardeners prefer untreated wood for vegetable beds.

How deep should a planter box be?

A depth of 8 to 12 inches suits most flowers and herbs. Deeper boxes hold moisture longer and suit vegetables with larger roots.

Do I need to line a wooden planter box?

A liner helps extend the life of the box, especially with untreated wood. Use a breathable landscape fabric or a thin plastic sheet with drainage holes punched through it.

Conclusion

With these planter box plans, a weekend and a few basic tools are enough to build a box that holds up outdoors. Pay attention to drainage gaps, exterior fasteners and finish, and the box will last for many seasons. Check your local rules on treated lumber before using it near edible plants.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.