Updated November 2026

Woodworking plans for vanity projects give you a clear path from rough lumber to a bathroom cabinet that holds up to daily moisture. In this guide you will work out the dimensions, build a basic face-frame box, and add a top and doors that fit square. The build suits a single-sink vanity about 30 inches wide and 21 inches deep, though you can scale the numbers to fit your space.

Plan the Dimensions and Cut List

Start by measuring the wall space and the sink or basin you plan to install. Most bathroom vanities stand 32 to 36 inches tall including the top, and a standard counter depth is 21 inches. Sketch the carcass, then write a cut list before you touch a board.

Shopping for one? See our guide: 7 Best Fixed Base Wood Routers for Woodworking in 2026.

Part Qty Dimensions (inches) Material
Sides 2 3/4 x 21 x 32 Plywood or solid wood
Top and bottom 2 3/4 x 21 x 28.5 Plywood
Back 1 1/4 x 28.5 x 31 Plywood
Face frame stiles 2 3/4 x 1.5 x 32 Hardwood
Face frame rails 3 3/4 x 1.5 x 28.5 Hardwood
Shelf 1 3/4 x 20.25 x 28.5 Plywood

Add an extra 1/8 inch to each length if you plan to trim to fit after assembly. Label each piece as you cut it so the carcass goes together without guesswork.

Build the Carcass With Strong Joinery

A vanity carcass lives in a humid room, so the joints need to hold through seasonal movement. Dadoes and rabbets give you glue surface and mechanical strength, and they keep the box square while the glue cures.

  1. Cut 1/4-inch dadoes 3/8 inch deep in the sides to receive the top and bottom.
  2. Rabbet the back edges so the 1/4-inch back panel sits flush.
  3. Dry-fit the box and check both diagonals. They should match within 1/16 inch.
  4. Apply glue to the dadoes, assemble, and clamp square. Let it cure for at least several hours before removing clamps.

For more on squaring and clamping, see Woodworking Clamps and Glue-Ups: Pressure and Prep and Woodworking Measuring Tools: Rules, Tapes and Squares.

Attach the Face Frame and Doors

Glue and pin the face frame to the front edge of the carcass, keeping the stiles and rails flush with the sides. Pocket screws work well here because they pull the frame tight while the glue sets. Hang doors on concealed hinges with a 1/8-inch reveal around each edge, then check that they close evenly before you finish.

If you are new to power tools, review Woodworking Safety Basics: The Hazards and Controls before running any cuts on the table saw or router.

Finish and Install

Sand to 150 grit, wipe off dust, and apply a water-resistant finish such as a marine-grade spar varnish or a waterborne polyurethane. Build up at least three coats, sanding lightly between them. Install the vanity level, anchor it into wall studs, and connect the plumbing last.

Common Mistakes

  • Skipping the diagonal check, which leaves the carcass racked and doors misaligned.
  • Using untreated solid wood for the bottom panel in a wet room, which can cup and split.
  • Cutting the top to final size before the sink template is confirmed.
  • Rushing the finish, which traps moisture and leads to peeling near the sink.
  • Mounting the cabinet without locating studs, which can pull out under the weight of a full basin.
  • A pocket-hole jig, which makes quick, strong face-frame joints without complex layout. View on Amazon
  • Concealed cabinet hinges with adjustment screws, which let you fine-tune door alignment after install. View on Amazon
  • A marine-grade spar varnish, which resists moisture better than standard interior finishes. View on Amazon

FAQ

What wood works best for a bathroom vanity?

Plywood with a sealed finish is stable and resists warping, and hardwoods like oak or maple suit the face frame. Avoid untreated softwoods in areas with frequent splashing.

How deep should a vanity be?

A standard depth is about 21 inches, which fits most bathrooms and leaves room for plumbing. Check your sink manufacturer’s specifications before you finalize the carcass.

Do I need a shop full of tools to build this?

A circular saw or table saw, a drill, clamps and a router cover most of the work. Adjust the joinery to match the tools you have.

Conclusion

With the cut list, dadoed carcass and water-resistant finish in place, you have a vanity that will serve for years. Check local building codes and consult a licensed plumber or electrician for any hookups behind the cabinet.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.