Updated November 2026
Bedside table plans woodworking projects are one of the most practical builds for a beginner, because the piece is small, the joinery is forgiving, and you finish with something you will use every day. This guide walks through a basic drawer-and-shelf bedside table, from the cut list to the final finish. The dimensions below suit a standard bed height of about 24 to 26 inches.
Plan the Dimensions and Cut List
Start by sketching the table to its real size. A common bedside table measures about 22 inches tall, 18 inches wide and 14 inches deep. Measure your mattress height first, since the top should sit roughly level with it or just below. Build your cut list from those numbers, then add 1/8 inch to each part for saw kerf and final sanding.
Shopping for one? See our guide: 7 Best Table Saws for Woodworking Projects Compared (2026).
- Two sides: 3/4 x 14 x 22 in (plywood or solid stock)
- Top and bottom: 3/4 x 14 x 18 in
- Back panel: 1/4 x 18 x 21 in (plywood)
- Drawer front: 3/4 x 5 x 17 in
- Drawer sides (2): 1/2 x 4 x 13 in
- Drawer back: 1/2 x 3 1/2 x 16 1/2 in
- Drawer bottom: 1/4 x 13 1/2 x 16 1/2 in
- Shelf: 3/4 x 12 1/2 x 16 1/2 in
Cut and Join the Carcass
Cut all parts to length and check them for square before you assemble anything. A table saw with a crosscut sled gives the cleanest ends, and a sliding miter saw works well for the shorter pieces.
- Cut a 1/4 inch groove 3/8 inch deep into the inside faces of the sides to hold the back panel.
- Cut dados 1/4 inch deep across the inside faces of the sides for the shelf and bottom, placed to match your drawer opening.
- Glue and clamp the carcass with the back panel captured in its groove. Check the diagonals; they should match within 1/16 inch.
If you are new to joinery, the Woodworking Techniques: Measure, Cut, Join, Sand, Finish overview and the notes in Woodworking Clamps and Glue-Ups: Pressure and Prep will help you get the glue-up right the first time.
Build and Fit the Drawer
Drawers are where many first builds go wrong, so cut the opening before you build the drawer. Measure the actual opening width and height, then make the drawer front 1/8 inch smaller on each side so it clears the carcass. Cut a 1/4 inch groove near the bottom edge of the drawer sides and front for the drawer bottom. Use a simple rabbet or dado joint at the front corners, glue and clamp, then slide the drawer bottom into its groove. Test-fit before the glue sets, and plane or sand the sides lightly until the drawer runs freely.
Sand and Finish
Sand progressively through 120, 150 and 180 grit, then wipe the surfaces with a damp cloth to raise the grain and knock down the dust. Apply your finish according to the manufacturer’s directions. Many owners prefer a wiping oil or water-based polyurethane for bedside pieces because they are easy to touch up. Let each coat dry fully before sanding lightly and adding the next.
Common Mistakes
- Cutting the drawer to the nominal opening instead of the measured one, which causes binding.
- Skipping the square check during glue-up, leaving the carcass racked.
- Using a back panel that is too thick for its groove.
- Applying finish over unsanded glue squeeze-out, which shows as dull spots.
Recommended Gear
- Bar clamps: Hold the carcass square while the glue cures. View on Amazon
- Random orbit sander: Speeds up flat sanding on the panels and top. View on Amazon
- Drawer slides: Offer smoother action than wood-on-wood runners if you prefer a metal option. View on Amazon
FAQ
What wood works best for bedside table plans woodworking projects?
Pine and poplar are easy to work and inexpensive, while oak and walnut give a more durable finish. Plywood works well for the sides and back because it resists movement.
How long does this build take?
Most builders can complete the carcass and drawer in a weekend, allowing extra time for glue drying and finish coats.
Do I need a table saw to build this?
A table saw makes the dados and grooves easier, but you can also use a router with a straight bit and a guide.
Conclusion
With accurate measurements and a careful glue-up, this bedside table is a solid first project that teaches dados, grooves and drawer fitting. Adjust the dimensions to suit your bed and your storage needs. Always follow tool safety guidance and consult a professional if you are unsure about a cut.
Related reading
- Simple Birdhouse Woodworking Plans: A Step-by-Step Build for Beginners
- Free Woodworking Birdhouse Plans: A Step-by-Step Build for Beginners
- Wood Router Table Plans: Build a Sturdy Router Table in 7 Steps
- Wood Router Table Plans Free: 4 Builds You Can Make This Weekend
- Creston Wood Router Table Plans: Build a Sturdy Table in 6 Steps
