Updated November 2026
Birdhouse and feeder plans let you build a nest box and a seed tray into one structure, so you can attract nesting birds and feed them from the same post. This guide gives you the layout, a cut list in general terms, the assembly order and the mistakes that cause trouble later. Most builders can finish a combined unit in a weekend with basic hand tools.
Choose a Combined Design First
Most birdhouse with feeder plans use one of two layouts. The first mounts a feeder tray on the front of a nest box, with the entrance hole above the tray. The second places a standalone feeder on a pole a few feet from the house. The front-mounted design is simpler and keeps everything on one post, but it can crowd the nest entrance if the tray is too deep. Decide which layout you want before you cut anything, because it changes the front panel dimensions.
Shopping for one? See our guide: Free Birdhouse Feeder Plans: 3 Best Build Guides for Beginners.
Keep the nest box interior sized for your target species. A wren or chickadee box needs a small entrance and a shallow floor. Bluebirds need a larger cavity. If your plan is for a particular bird, check a species-specific guide such as Wren Birdhouse Plans Free: Build a Cedar House in One Weekend or Western Bluebird Birdhouse Plans: Build a Nest Box in One Afternoon before you settle on dimensions.
Cut Lists and Materials
Use rough cedar, cypress or untreated pine at about 3/4 inch thick. These woods resist rot and hold screws well. Avoid pressure-treated lumber, painted or stained surfaces, and any wood with chemical preservatives, because birds can be harmed by fumes and residues.
- Two side panels, same height, with the back panel slightly taller so the roof sits at a pitch.
- One front panel with the entrance hole drilled about 1 1/4 inches in diameter for chickadee-sized birds, or larger for bluebirds. Keep the hole 6 to 8 inches above the floor.
- One floor panel with four to six drainage holes, each about 1/4 inch.
- One feeder tray panel with a raised lip on three sides so seed stays put.
- Two roof panels, sized to overhang the front by 2 inches and the back by about 1 inch.
- Exterior screws (stainless or galvanized), wood glue, and a short mounting bracket.
Measure your own boards before cutting. Lumber thickness varies, and a 1/16-inch error on each side can leave you with a gap at the roof line.
Assembly Steps
- Drill the entrance hole and drainage holes first, while the panels are still flat and easy to clamp.
- Glue and screw the floor between the side panels. Keep the floor flush with the bottom edges.
- Attach the back panel, then the front panel. Leave the front panel’s top edge free if you plan to access the nest for cleaning.
- Mount the feeder tray to the front, below the entrance hole. Use two screws from the inside so the tray is firm but removable.
- Fit the roof panels with a slight overhang front and back, and secure them with screws placed so you can open the roof later.
- Apply a finish only to the exterior, if at all. Leave the interior bare.
Mounting and Placement
Mount the combined unit 5 to 10 feet off the ground on a post or wall. Face the entrance away from prevailing winds and avoid direct afternoon sun, which can overheat a nest. Keep the feeder tray at least 3 feet from any window to reduce collision risk. Cats and squirrels are a real threat, so use a baffle on the post if predators are common in your yard.
Common Mistakes
- Placing the entrance hole too close to the feeder tray, which lets predators reach the nest.
- Using treated wood or paint on the interior.
- Leaving drainage holes out, which traps moisture and leads to mold.
- Making the feeder tray too deep, so seed spoils before birds eat it.
- Fixing the roof permanently, so you cannot clean the box between seasons.
Recommended Gear
A countersink bit helps you set screws flush so the feeder tray and roof sit evenly. View on Amazon
A pair of clamps holds the side and front panels square while glue cures. View on Amazon
Stainless exterior screws resist rust and stay tight through seasonal swelling. View on Amazon
FAQ
Can I use one plan for both a birdhouse and a feeder?
Yes, but the entrance hole size and feeder placement must match the species you want to attract. A single plan works best when you keep the feeder tray below and away from the nest opening.
What wood is safest for birds?
Untreated cedar, cypress or pine is the usual choice. Avoid pressure-treated lumber, paint on the interior and any chemical finish that birds might ingest or breathe.
How often should I clean a combined birdhouse and feeder?
Clean the nest box once a year after the nesting season ends, and scrub the feeder tray every few weeks to prevent mold and disease.
Conclusion
A well-planned combined unit gives birds a nest site and a feeding spot on one post. Pick your layout, cut to a clear list, and place the house with predators and sun in mind. Check your local wildlife guidelines before you start, especially for protected species.
