Updated November 2026

Cedar fence picket birdhouse plans give you a simple, weather-resistant nest box built from a single standard fence picket and a few scraps. In this guide you will cut the parts, assemble the house with screws, and finish it so it holds up outdoors for years. The whole build takes a weekend, including drying time for the finish.

Cut List and Materials

Cedar resists rot and warping better than most softwoods, which is why it suits outdoor nest boxes. A standard fence picket is usually about 5/8 inch thick and 5½ inches wide, so you can cut the house from one board. Use exterior-grade stainless or galvanized screws, since plain steel screws stain the wood and rust over time.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • One cedar fence picket, roughly 5/8 in. x 5½ in. x 6 ft (cut to length below)
  • Front panel: 5/8 in. x 5½ in. x 8 in., with a 1-1/8 in. entry hole cut 6 in. above the bottom edge
  • Back panel: 5/8 in. x 5½ in. x 13 in., taller than the front so it extends above the roof
  • Two side panels: 5/8 in. x 5½ in. x 8 in., cut with a 6-degree angle on the top edges so the roof sits flush
  • Bottom: 5/8 in. x 4 in. x 4 in., with drainage gaps of about 1/4 in. at each corner
  • Roof: 5/8 in. x 6 in. x 6 in. (two pieces if you want a split roof for easy cleaning)
  • Exterior screws: 1¼ in. stainless, roughly 16 needed

Step-by-Step Assembly

Cut the Parts Accurately

Set your miter saw or table saw to the exact dimensions above and cut every piece before you assemble anything. Mark the entry hole on the front panel and drill it first with a hole saw or Forstner bit, because drilling an assembled box is awkward. Keep your hole center exact so the entrance sits well above the floor of the house.

Assemble the Box

Lay the back panel flat and attach the two side panels so their outer edges sit flush with the back. Drive two screws through each side into the back panel, then pre-drill near the ends to prevent splitting. Attach the front panel last, keeping the edges aligned. Check for square by measuring the diagonals; they should match within 1/16 inch.

Add the Bottom and Roof

Fasten the bottom so the drainage gaps face outward. Attach the roof so it overhangs the front by about 1 inch to shed rain away from the entrance. Leave the roof hinged or secured with a single screw if you plan to clean the box each fall.

Finishing and Mounting

Leave the interior unfinished and unpainted. Birds need a rough surface to grip, and paint or stain fumes can harm nesting birds. Apply an exterior finish only to the outside, and let it cure fully before mounting. Roughen the inside walls with a file or a few scored lines if the wood is very smooth.

Mount the house on a pole or fence post about 5 to 10 feet off the ground, facing away from prevailing winds and direct afternoon sun. For more on matching the entry size to the species you want, see Wren Birdhouse Plans Free: Build a Cedar House in One Weekend and Plans for Wren Birdhouse: A Step-by-Step Guide With Cut List.

A hole saw or Forstner bit set makes the entry hole clean and accurate, which matters more than anything else in a small box. Drive the screws with a cordless drill and matching bit so you do not split the cedar near the edges. A small set of clamps keeps the panels aligned while you fasten them.

  • Forstner bit set: cuts a clean, flat-bottomed entry hole without tearout. View on Amazon
  • Cordless drill driver: drives screws quickly and lets you adjust torque to avoid stripping the cedar. View on Amazon
  • Bar clamps: hold panels square while you drive the screws. View on Amazon

Common Mistakes and Tips

  • Skipping drainage gaps in the floor, which lets water pool and rot the bottom.
  • Using painted or treated lumber inside the box, which can harm nesting birds.
  • Drilling the entry hole too large, which invites starlings and other competitors.
  • Mounting the box in full sun, where the interior can overheat in summer.
  • Making the box too smooth inside, which can keep fledglings from climbing out.

FAQ

What size entry hole should a cedar picket birdhouse have?

A 1-1/8 inch entry hole suits many small songbirds such as chickadees and wrens. Check the species you want to attract before drilling, since bluebirds and other species need different openings.

Can I use pressure-treated wood instead of cedar?

Pressure-treated wood is not recommended for nest boxes because the chemicals can harm birds. Cedar is a safer choice because it is naturally rot-resistant and untreated.

How often should I clean the birdhouse?

Clean the box once a year after the nesting season ends, removing old nesting material to reduce parasites. Do not clean it while birds are actively nesting.

Conclusion

With one fence picket and a few careful cuts, you can build a durable cedar nest box in a single weekend. Keep the interior rough, the drainage gaps open, and the entry hole sized for your target species. Mount it well, and it should serve birds for many seasons.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.