Updated November 2026

Cedar picket birdhouse plans give you a simple, weather-resistant nest box built from a single standard fence picket. This guide walks through the cut list, assembly order, and the entrance-hole and ventilation details that matter most for songbirds. Most builders can finish one in an afternoon with basic hand tools.

Materials and Cut List for a Cedar Picket Birdhouse

A standard cedar fence picket, roughly 5/8 inch thick and 5.5 inches wide, is the starting point for this design. Cedar resists rot without chemical treatment, which matters because a birdhouse sits outdoors year-round. Plan on the following pieces, cut from one picket:

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

Part Quantity Dimensions (inches)
Front panel 1 5/8 x 5.5 x 9
Back panel 1 5/8 x 5.5 x 12
Side panels 2 5/8 x 4.5 x 9 (angled top)
Floor 1 5/8 x 4.5 x 4.5
Roof 1 5/8 x 6.5 x 7

Cut the back panel longer than the front so it extends above the roof line and gives you a mounting point. Mark each piece with its name before cutting, since the picket width is close to the size of several parts and mixing them up is easy.

Cutting and Preparing the Parts

Use a miter saw or a hand saw with a guide. Set the front panel and side panels to 9 inches, then mark a 45-degree bevel on the top of each side panel so the roof sits flush. Cut the floor to 4.5 inches square and drill four 1/4-inch drainage holes through it, one in each corner. Sand all faces lightly with 120-grit paper, and round the entrance edge slightly to reduce wear on the bird’s feathers.

Assembly Steps for the Nest Box

  1. Lay the floor flat and attach the two side panels to its edges with exterior-grade wood glue and 1-1/4-inch galvanized or stainless exterior screws. Pre-drill every screw hole to avoid splitting the cedar.
  2. Attach the front panel between the sides, keeping its bottom edge flush with the floor. Check that the box is square before the glue sets.
  3. Fasten the back panel so it sits flush with the sides and extends above the roof line.
  4. Drill the entrance hole in the front panel. For most cavity-nesting songbirds, a 1-1/8-inch to 1-1/2-inch opening is standard. Measure from the floor so the hole sits about 6 to 8 inches above it.
  5. Attach the roof with two screws through the top of the sides, leaving a small overhang of about 1 inch on the front and sides for rain protection.
  6. Drill two 3/16-inch ventilation holes near the top of each side panel, just under the roof.

Mounting and Placement Guidelines

Mount the box 5 to 10 feet off the ground on a post, fence line, or tree, facing away from prevailing winds and direct afternoon sun. Avoid placing it near feeders, since busy feeding activity can stress nesting birds. Attach it with a single screw through the back panel so you can open it for cleaning.

Use an entrance size that matches the bird you want to attract. A 1-1/8-inch hole is typical for chickadees and wrens, while larger openings invite starlings and sparrows that compete for nest sites.

Common Mistakes to Avoid

  • Skipping pre-drilled holes, which splits the picket and loosens joints over time.
  • Using interior wood glue or uncoated screws, which fail outdoors within a season or two.
  • Omitting the floor drainage holes, leaving nesting material wet after rain.
  • Choosing an entrance hole that is too large for the species you hope to attract.
  • Mounting the box where cats or raccoons can reach it easily.

A reliable drill and a set of bits make the pilot holes and entrance cut much easier, and a hole saw or Forstner bit gives clean round openings. Look for a Forstner bit set and exterior wood glue when shopping.

  • A cordless drill driver speeds up screw driving and pilot drilling. View on Amazon
  • Forstner bits produce clean, flat-bottomed entrance holes with minimal tear-out. View on Amazon
  • Exterior wood glue is rated for outdoor joints that see moisture. View on Amazon

If you want more variations before you start, compare the design with Fence Picket Birdhouse Plans: Build a Cedar Birdhouse in a Weekend and Wren Birdhouse Plans Free: Build a Cedar House in One Weekend, which use similar materials and dimensions.

FAQ

What size lumber works best for cedar picket birdhouse plans?

A standard 5/8-inch-thick cedar fence picket, about 5.5 inches wide, works well and needs no milling. It gives enough thickness for screws to hold firmly.

How big should the entrance hole be?

Most small songbirds, such as wrens and chickadees, do well with a 1-1/8-inch hole. Larger species need bigger openings, so check the requirements for the bird you want to attract.

Should I paint or stain a cedar birdhouse?

Cedar is naturally rot-resistant, so an unfinished box is fine. If you do finish it, use a nontoxic exterior stain or paint on the outside only, and leave the interior bare.

Conclusion

A cedar picket birdhouse is one of the quickest projects you can build with basic tools and one board. Follow the cut list, pre-drill your screw holes, and size the entrance for your target species. With those steps, you will have a nest box that lasts for many seasons.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.