Updated November 2026

Chestnut backed chickadee birdhouse plans give you a small, well-ventilated nest box sized for these tiny cavity nesters, which typically use holes around 1-1/8 inches across. This guide walks you through a simple box you can build from one 1×6 cedar board in an afternoon, with a cut list, assembly steps, and the details that keep the nest dry and predator-resistant.

Dimensions and Cut List for a Chestnut Backed Chickadee Box

Chestnut-backed chickadees are small, and they do well in a box with a floor of about 4 x 4 inches and an interior height of roughly 8 to 9 inches. Build from 3/4-inch cedar or another rot-resistant softwood, and keep all interior surfaces unfinished so the birds can grip them.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • (2) Front and back panels: 3/4 x 5-1/2 x 9 inches
  • (2) Side panels: 3/4 x 4-1/2 x 9 inches (sized to fit inside the front and back, or cut to sit between them, as you prefer)
  • (1) Floor: 3/4 x 4 x 4 inches
  • (1) Roof: 3/4 x 6 x 7 inches, with a slight overhang on all sides

Step-by-Step Assembly

  1. Cut all pieces to the sizes above. Square the ends with a miter saw or a table saw sled so the walls meet flush.
  2. Drill the entrance hole in the front panel, about 6 inches up from the floor, centered side to side. Use a 1-1/8 inch hole saw or Forstner bit. Clean any splinters from the inside edge.
  3. Drill drainage holes in the floor, four 1/4-inch holes at the corners, and ventilation holes near the top of each side panel.
  4. Assemble the box with exterior-grade wood glue and galvanized 1-1/4 inch exterior screws. Pre-drill every screw to prevent splitting. Keep the front and back panels overlapping the sides so the walls stay square.
  5. Attach the floor so it sits slightly recessed, which lets water drain out instead of pooling.
  6. Add the roof with hinges or a single screw on one side so you can open it for cleaning. Leave a small gap for ventilation under the roof edge.

Mounting and Placement

Mount the box 4 to 6 feet off the ground on a tree trunk or fence post, facing away from prevailing winds and afternoon sun. Chickadees often nest in mixed woodland, so a spot near conifers or trees with dead snags is ideal. Avoid placing the box near bird feeders, which can attract predators and crowd nesting territory.

Common Mistakes

  • Using treated lumber or painted interiors, which can harm nesting birds.
  • Making the entrance hole too large, which lets in predators and starlings.
  • Skipping the floor drainage holes, which traps moisture and encourages mold.
  • Mounting the box too low, where cats and raccoons can reach it.
  • Failing to clean the box after each season to prevent parasite buildup.
  • Forstner bit set makes clean, accurate 1-1/8 inch entrance holes without tearout. View on Amazon
  • Galvanized exterior wood screws resist rust and hold up to outdoor weather. View on Amazon
  • Exterior wood glue keeps joints tight when exposed to rain and temperature swings. View on Amazon

FAQ

What entrance hole size should I use for chestnut backed chickadees?

A hole of about 1-1/8 inches works well for chickadees while keeping larger birds out. Measure your bit before drilling, since hole saws vary slightly.

Can I use pine instead of cedar?

Yes, but use untreated pine and expect it to weather faster. Cedar resists rot better and holds up longer outdoors.

When should I clean the box?

Clean it once after the nesting season ends, removing old nest material and scrubbing the interior with hot water. Do not use chemical cleaners.

Conclusion

With a 4 x 4 inch floor, a 1-1/8 inch entrance, and proper drainage, this box gives chestnut backed chickadees a safe, dry place to raise their young. Build it from untreated cedar, mount it at a safe height, and check it each season. For more designs suited to small cavity nesters, browse our Birdhouse Plans for Chickadees: A Step-by-Step Guide for Beginners and Black Capped Chickadee Birdhouse Plans: A Step-by-Step Build Guide.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.