Updated November 2026

Cutting notches in wood with a router gives you clean, square-bottomed recesses for shelf dadoes, half-lap joints and stopped slots. You will set up a straight bit, clamp a guide, and remove the waste in shallow passes so the notch comes out flat and the right width. The method takes about 15 minutes to learn and works on everything from pine boards to hardwood panels.

Choose the Right Bit and Setup

A straight router bit matching the notch width is the simplest choice. For a 3/4-inch wide notch, use a 3/4-inch straight bit, not a bit that is almost the right size and then widened by sliding the router. Many notches call for a bit with a shank that matches your collet, so check the shank diameter before you buy.

Shopping for one? See our guide: 5 Best CNC Router Wood Cutting Machines for Hobbyists in 2026.

Use a plunge router if you can. It lets you lower the bit into the wood at a set point and stop at an exact depth, which is easier to control than a fixed-base router that has to be tipped in.

Mark the Notch and Clamp a Guide

Mark the notch edges on the workpiece with a pencil and a square. Then clamp a straight guide, such as a scrap board or a commercial edge guide, so the router base rides a fixed line. Set the guide so the bit’s cutting edge lands exactly on your line, measured from the bit’s outer edge to the guide face.

Clamp the workpiece firmly to a bench or sacrificial board. Movement during the cut is the most common cause of ragged notch walls.

Cut the Notch in Shallow Passes

  1. Set the bit depth to no more than 1/4 inch for the first pass. Hardwoods and deep notches benefit from even shallower passes, around 1/8 inch.
  2. Plunge the spinning bit into the start point slowly, then move the router along the guide from left to right, against the bit’s rotation.
  3. Stop at the far end, lift the bit clear, and return to the start.
  4. Increase depth by the same amount for each pass until you reach the final notch depth. A final pass of about 1/16 inch leaves a smooth floor.
  5. Clean the bottom of the notch with a chisel if you need inside corners squared, since a standard round-corner bit cannot cut true square corners.

Check the Fit and Finish

Test the notch with a scrap piece of the same thickness before cutting the real part. Measure the width at both ends and the middle. If the walls taper, the guide has shifted or the router rocked during the cut. If the floor looks rough, the last pass was too deep or the feed was too fast.

Feed Direction and Speed

Feed the router against the bit’s rotation so the cutter pulls the router against the guide rather than away from it. Keep a steady speed. Pausing in one spot leaves burn marks, and rushing causes tear-out on the exit side.

Common Mistakes

  • Cutting the full depth in one pass, which strains the motor and tears the wood.
  • Setting the guide by eye instead of measuring from the bit’s outer edge.
  • Forgetting that the router moves the same direction as the guide edge, leading to a notch that is off by the bit’s radius.
  • Using a dull bit, which leaves fuzzy walls and burn marks.
  • Skipping a scrap test cut before working on the final piece.
  • Plunge router: Lets you set exact depth and start cuts in the middle of a board. View on Amazon
  • Straight router bit set: Gives you the right width for common notch sizes without buying bits one at a time. View on Amazon
  • Edge guide for routers: Keeps the router base on a straight line for consistent notch walls. View on Amazon

FAQ

Can I cut a notch with a router without a guide?

You can, but accuracy suffers. A clamped straight guide or a template keeps the notch walls parallel and the width consistent.

How deep should each pass be?

Keep each pass to about 1/4 inch in softwood and about 1/8 inch in hardwood. Shallower passes produce cleaner walls and reduce strain on the router.

Can a router make square inside corners in a notch?

A standard straight bit leaves rounded corners. Finish the corners with a chisel, or use a square-end bit made for dadoes if you need crisp corners.

Conclusion

Cutting notches in wood with a router comes down to the right bit, a clamped guide and shallow passes. Test on scrap first, and check your measurements before each pass. With these steps, your notches will fit cleanly on the first try.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.