Updated November 2026

DIY barn birdhouse plans give you a small, weather-tight nest box shaped like a miniature barn, built from a few boards and basic tools. By the end of this guide you will have a cut list, the key dimensions for the entrance hole and ventilation, and an assembly sequence that holds together outdoors for years. The design works well for bluebirds, chickadees and wrens when the interior is sized correctly.

Gather Materials and Cut the Pieces

Use cedar, cypress or pine that is at least 3/4 inch thick. Cedar resists rot and does not need paint, which matters because paint and stains can harm nesting birds. Plan on a board about 6 inches wide and 6 feet long, plus scrap for the roof trim.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • Front and back walls: 2 pieces, 6 inches wide by 9 inches tall, with the top corners cut at 45 degrees to form the gable peak.
  • Side walls: 2 pieces, 5 1/2 inches wide by 9 inches tall, with the top edges cut at the roof pitch.
  • Floor: 1 piece, 5 1/2 inches by 5 1/2 inches.
  • Roof panels: 2 pieces, 7 inches by 8 inches, overhanging the walls by about 1 inch on each edge.

Mark every piece with its name before you cut. Barn roofs are easy to get wrong when the two roof panels differ by even 1/8 inch, so cut them as a matched pair.

Drill the Entrance Hole and Ventilation

Drill the entrance hole in the front wall, centered about 6 inches up from the floor. Use a 1 1/2-inch hole for bluebirds and a 1 1/4-inch hole for chickadees and wrens. Measure from the bottom of the hole to the floor so the bird has a clean drop into the nest chamber.

Add ventilation by drilling four 1/4-inch holes near the top of each side wall. Drill drainage holes, four 1/4-inch holes, through the floor. Without these, moisture builds up and the nest becomes damp.

Assemble the Box

  1. Glue and screw the floor between the two side walls, keeping the bottom edges flush.
  2. Attach the front and back walls to the assembly with exterior wood glue and 1 1/4-inch exterior screws. Drill pilot holes first to prevent splitting.
  3. Check that the box is square by measuring the diagonals. They should match within 1/8 inch before the glue sets.
  4. Fasten the roof panels with hinges or screws so the roof lifts for annual cleaning.
  5. Add a 1/2-inch rough-cut lip or a few shallow grooves under the entrance hole so fledglings can grip the edge.

Mount the Birdhouse Safely

Hang or mount the house 5 to 10 feet off the ground, facing away from prevailing winds and direct afternoon sun. Clear a flight path of at least 10 feet. Use a predator guard if cats or raccoons are common in your area, and do not place the box near feeders where crowding can stress the birds.

  • Exterior wood glue: Holds joints tightly and is rated for outdoor use, which keeps seams closed through freeze and thaw cycles. View on Amazon
  • Stainless steel exterior screws: Resist corrosion from rain and do not stain cedar the way plain steel can. View on Amazon
  • Forstner bit set: Produces clean, flat-bottomed entrance holes without tear-out on the outside face. View on Amazon

Common Mistakes to Avoid

  • Using treated lumber or painted surfaces inside the nest chamber, which can expose birds to harmful chemicals.
  • Making the entrance hole too large, which lets in predators and European starlings.
  • Skipping the floor drainage holes, which leads to mold and damp nests.
  • Mounting the box in full sun, where interiors can overheat in summer.
  • Forgetting to open the roof and clean out old nesting material after each season.

For more builds in the same style, see Free Barn Style Birdhouse Plans: A Step-by-Step Build With Cut List and Barn Style Birdhouse Plans: A Step-by-Step Build With Cut List. If you want a smaller project first, Simple Cedar Birdhouse Plans: A Step-by-Step Build in One Weekend uses similar joinery with fewer parts.

FAQ

What wood is best for a DIY barn birdhouse?

Cedar is the most common choice because it resists rot and insects without chemical treatment. Pine works too if you seal only the exterior and leave the interior bare.

What entrance hole size should I use?

A 1 1/2-inch hole suits bluebirds, and a 1 1/4-inch hole suits chickadees and wrens. Smaller holes keep out larger birds and many predators.

When should I clean out the birdhouse?

Clean it after the nesting season ends, typically in late summer or early fall. Remove old nesting material and check the drainage holes are clear.

Conclusion

With accurate cuts, the right entrance size and proper drainage, this barn design gives cavity-nesting birds a safe place to raise young. Build it once, mount it correctly, and it can serve for many seasons with simple annual maintenance. Consult a local wildlife or bird conservation group if you need species-specific guidance.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.