Updated November 2026
This guide gives you a complete set of DIY wooden birdhouse plans for a simple, sturdy nest box that suits common backyard songbirds. You will get a cut list, assembly steps, drilling dimensions and mounting advice, all built from one 1×6 cedar or pine board. Plan on a build time of a few hours, plus paint or finish drying time.
Cut List and Materials
The design below uses one 1×6 board roughly 6 feet long, which is standard nominal lumber (the actual width is about 5-1/2 inches). Untreated cedar or pine works well because both resist rot without chemicals that could harm birds.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
- Two side panels: 5-1/2 in. wide × 9 in. long (one end cut square, the other at a 4-inch top-to-front angle to form the roof slope)
- Front panel: 4 in. wide × 11 in. long, with the top cut at the same slope as the sides
- Back panel: 5-1/2 in. wide × 12 in. long, extending above the sides to form the rear roof edge
- Floor: 4 in. × 4 in. square, with 1/4-inch drainage holes drilled in each corner
- Roof: 6 in. × 7 in. rectangle, cut from the same board or a separate piece
- Hardware: 1-1/4 in. exterior wood screws or galvanized nails, wood glue, and a few 1-1/2 in. screws for the roof hinge
Step-by-Step Assembly
Work on a flat surface and check square at each joint before you drive fasteners. A small error in the front panel will make the whole house lean.
- Cut all pieces to the lengths above. Mark the entrance hole location on the front panel before assembly.
- Drill the entrance hole through the front panel, centered 6 to 7 inches above the floor line. For a wren-sized house, use a 1-1/8 in. diameter hole. For bluebirds, use 1-1/2 in.
- Glue and screw the floor between the side panels, leaving the floor slightly recessed to prevent water pooling.
- Attach the back panel first, then the front, keeping all edges flush at the bottom.
- Fit the roof so it overhangs the front by about 2 inches. Attach it with a hinge or a single screw so you can open the house for cleaning each season.
- Drill ventilation holes near the top of each side panel, about 3/8 inch in diameter, and drill drainage holes in the floor.
Mounting Height and Location
Mount the house 5 to 10 feet off the ground on a pole or fence post. Face the entrance away from prevailing wind and avoid positions where direct afternoon sun would heat the box.
Recommended Gear
- Forstner bit set gives clean, flat-bottomed entrance holes that are easier to get exact than spade bits. View on Amazon
- Exterior wood glue adds strength to the joints so the house holds together through freeze-thaw cycles. View on Amazon
- Corrosion-resistant exterior screws keep the box from splitting at the fastener points and avoid rust stains. View on Amazon
Common Mistakes to Avoid
- Skipping drainage holes, which lets moisture collect and rot the floor.
- Using treated lumber or painting the interior, both of which can harm nesting birds.
- Drilling an oversized entrance hole, which invites starlings and house sparrows.
- Placing the house in full sun, where interiors can overheat in summer.
- Forgetting to open and clean the box after each nesting season.
FAQ
What wood is best for DIY wooden birdhouse plans?
Untreated cedar, pine or cypress are the most common choices. They are naturally weather resistant and safe for birds when left unfinished on the inside.
What size entrance hole should I drill?
It depends on the species. A 1-1/8 inch hole suits wrens and chickadees, while a 1-1/2 inch hole suits bluebirds.
Should I paint or stain the birdhouse?
You can paint or stain the exterior with a light, non-toxic finish in muted colors. Leave the interior bare so the wood can breathe and no fumes remain.
Conclusion
With one 1×6 board and basic tools, you can build a durable nest box that welcomes birds for years. Follow the cut list, keep the entrance hole sized correctly, and clean the house each fall for the best results.
