Updated November 2026
This guide gives you a complete set of double birdhouse planter plans: two nest boxes joined into one planter that holds soil and flowers on the top and bird nesting space below. You will get a cut list, assembly steps, and the drainage and ventilation details that keep both the plants and the birds healthy. Most builders can finish the frame in an afternoon with basic tools.
Cut List and Materials
Use cedar, pine, or another rot-resistant softwood at least 3/4 inch thick. Cut all pieces to the dimensions below, then label each part before you start assembly.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
| Part | Qty | Dimensions |
|---|---|---|
| Front and back panels | 2 | 10 in x 12 in |
| Side panels | 4 | 6 in x 12 in |
| Center divider | 1 | 6 in x 12 in |
| Bottom panels (planter floors) | 2 | 6 in x 6 in |
| Roof panels | 2 | 7 in x 10 in |
Cut two entrance holes in the front panels, each 1-1/2 inches in diameter, centered about 8 inches up from the bottom edge. Drill 1/4-inch drainage holes in each planter floor and ventilation slots near the top of each side panel.
Assembling the Two Chambers
Build each nest box as its own unit, then join them with the center divider. Working in pairs keeps the walls square and makes the final assembly easier.
- Glue and screw the side panels to the front and back panels of each chamber. Use exterior wood glue and 1-1/4 inch exterior screws, drilling pilot holes first.
- Attach the bottom panel to each chamber so that it sits flush with the sides. Leave the drainage holes facing down.
- Fasten the center divider between the two chambers, making sure it is square to the front panel.
- Check both chambers with a square and clamp the assembly until the glue sets, usually a few hours.
- Attach the roof panels with a slight overhang on the front and back to shed rain.
Planter Setup and Finishing
The top of each chamber becomes a planting bay, so line the inside with landscape fabric or a thin layer of gravel before adding potting soil. This keeps the soil from washing out the drainage holes.
Finishing the Wood
Sand all surfaces to 120 grit, then apply an exterior, bird-safe finish to the outside only. Never coat the inside of the nest chambers, and let every coat cure fully before you fill the planters.
Mounting Options
Hang the planter from a sturdy bracket or mount it on a post at least 5 feet off the ground. Position the entrance holes away from the prevailing wind and direct afternoon sun.
Tips and Common Mistakes
- Skipping the drainage holes leads to waterlogged soil and rotting floors.
- Cutting the entrance holes larger than 1-1/2 inches invites predators and starlings.
- Using treated lumber or unsealed pine near plants can harm both roots and birds.
- Leaving sharp screw tips exposed inside the nest chambers can injure nestlings.
- Planting without a barrier lets soil wash into the nest space during heavy rain.
Recommended Gear
- Exterior wood glue: A waterproof glue rated for outdoor use keeps the joints from failing when the planter gets wet. View on Amazon
- Exterior wood screws: Stainless or coated screws resist rust and keep the frame tight through seasonal swelling. View on Amazon
- Drill and bit set: A cordless drill with a sharp bit set makes clean pilot holes and entrance cuts. View on Amazon
If you enjoy this style of build, the Simple Cedar Birdhouse Plans: A Step-by-Step Build in One Weekend covers a similar joinery approach for a single nest box. Builders wanting a different species focus can also review Wren Birdhouse Plans PDF: A Step-by-Step Build With Cut List for smaller entrance sizing.
FAQ
What wood works best for a double birdhouse planter?
Cedar is the most common choice because it resists rot and stays stable outdoors. Untreated pine also works if you seal the exterior well.
How big should the entrance holes be?
Most small songbirds use holes about 1-1/4 to 1-1/2 inches across. Check the species you hope to attract before you cut.
Can I plant flowers directly in the nest chambers?
The planting bays sit on top of the nest boxes, so flowers go in the top section only. Keep soil out of the nest spaces to protect the birds.
Conclusion
With the cut list and assembly steps above, you can build a double planter that gives both your garden and local birds a place to thrive. Take time with the drainage holes and finish, and the planter will last for many seasons. Measure twice before each cut, and the joints will stay tight.
