Updated November 2026
A dovecote birdhouse is a multi-compartment nest box shaped like a small tower with a pitched roof, and it suits doves, pigeons and other cavity nesters that like a sheltered perch. This guide gives you the layout, a practical cut list and the build sequence you need to finish a sturdy dovecote in a single weekend. The dimensions here are a sound starting point, so check them against the plans you download before you cut.
Choose the Right Plan Before You Cut
Most free dovecote plans in PDF form fall into two types: a single-tower design with stacked compartments, and a larger multi-room unit with a central post. The single-tower version is the easier first build because it uses fewer parts and fewer joints. If you find a plan, confirm it lists a full cut list, an entrance hole diameter and a drainage or ventilation detail. Plans missing any of these are usually incomplete.
Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.
Cut the Parts Accurately
Use 3/4-inch exterior-grade plywood or rough cedar for the walls, floor and roof. Cedar and cypress resist rot without chemical treatment, which matters for an outdoor structure that stays wet. Cut the parts in the order listed on your plan, and mark each piece with its name on the back side so you do not mix up the compartment walls with the roof panels.
- Front and back walls: two pieces, with entrance holes marked at the same height
- Side walls: two pieces, one per compartment side
- Compartment dividers: one per level, sized to the inside width
- Floors: one per compartment, with four 1/4-inch drain holes each
- Roof panels: two angled pieces with a 2-inch overhang on the front and back
- Perch rod: one 3/8-inch dowel, about 6 inches long
Assemble the Compartments
Build each compartment as a separate box first, then stack them. Glue and screw each joint with exterior-rated wood glue and galvanized or stainless deck screws. Pre-drill every screw hole within 1/2 inch of an edge to prevent splitting. Keep the inside surfaces rough or lightly scored so young birds can grip the walls when they climb toward the entrance.
Set the Entrance Holes
Drill entrance holes at the height specified on your plan, usually about 3 inches above the floor. Use a hole saw matched to the diameter on the plan. A hole that is too large lets predators reach in, and one that is too small blocks the birds you want to attract.
Finish, Mount and Ventilate
Leave the interior unfinished and apply two coats of exterior-grade, bird-safe finish to the outside only. Stack the compartments, fix the roof, and attach a mounting bracket or pole on the back. Mount the house 6 to 12 feet off the ground in a spot with morning sun and some shade in the afternoon. Confirm the drain holes are open and the roof overhang shields the entrances from rain.
Common Mistakes
- Skipping drain holes, which lets water pool and rot the floors.
- Enlarging entrance holes to make them easier to see, which exposes nests to predators.
- Using pressure-treated wood with copper-based preservatives on interior surfaces.
- Mounting the house in full sun all day, which can overheat the compartments.
- Cutting roof panels without accounting for the overhang, leaving the entrances exposed to rain.
Recommended Gear
- Hole saw set: Lets you cut clean entrance holes to the exact diameter your plan calls for. View on Amazon
- Exterior wood glue: Holds the compartment joints under weather cycling better than standard glue. View on Amazon
- Stainless steel deck screws: Resist rust from outdoor moisture and do not stain the cedar. View on Amazon
If you are new to birdhouse builds, you may also find Free Printable Birdhouse Plans: Step-by-Step Guide for Beginners useful for basic joinery. For a simpler starter project, One-Board Birdhouse Plans Free: Build a Cedar House in One Afternoon uses fewer cuts. Larger builds are covered in Large Birdhouse Plans Free: 4 Builds for Owls, Kestrels and Wood Ducks.
FAQ
Can I use pressure-treated lumber for a dovecote?
You can, but use it only on exterior surfaces and avoid interior walls and floors. Choose a product labeled safe for wildlife structures, and let it dry fully before mounting.
How high should a dovecote be mounted?
Most builders mount dovecotes 6 to 12 feet off the ground. Higher placement makes it harder for ground predators to reach the entrances.
Do I need to clean the dovecote between seasons?
Yes. Remove old nesting material once the season ends, scrub the floors with a dilute bleach solution, rinse, and let the house dry completely before the next nesting period.
Conclusion
A well-built dovecote comes down to accurate cuts, correct entrance sizes and proper drainage. Follow the cut list, check each dimension against your PDF plan, and mount the house where it gets morning sun. With those steps done, you will have a durable nest box that lasts for many seasons.
