Updated November 2026

End table plans woodworking enthusiasts can follow fall into a few reliable designs, and most of them come down to the same core: a flat top, four legs, a stretcher or apron system, and joinery that holds up to daily use. This guide walks through how to pick a design, lay out a cut list, and assemble a simple square end table you can finish in a weekend.

Choose a Design and Size It Correctly

Standard end tables sit between 22 and 26 inches tall, which keeps the top level with a sofa arm. A top about 18 to 22 inches square works for most living rooms. Sketch the design first, then write down every part’s finished dimension before you touch any stock. Woodworking plans for end tables usually include a cut list for exactly this reason: it turns a rough idea into numbers you can check.

Shopping for one? See our guide: 7 Best Table Saws for Woodworking Projects Compared (2026).

Build the Cut List and Prepare Stock

For a basic 20-inch square table about 24 inches tall, a typical cut list looks like this:

Part Qty Finished size (inches)
Legs 4 1-1/2 x 1-1/2 x 23-1/4
Apron (long) 2 3/4 x 3 x 16
Apron (short) 2 3/4 x 3 x 16
Top 1 3/4 x 20 x 20

Cut a little long, joint and plane your stock flat, then trim to final length. Check each board with a square and a straightedge. Woodworking measuring tools such as a steel rule and a combination square matter more here than almost anywhere else in the build; small errors compound fast across four legs.

Cut the Joinery and Assemble the Base

Mortise-and-tenon joints give the strongest result for the apron-to-leg connection. Cut the mortises in the legs first, then cut tenons on the aprons to fit with a slight snug fit. If you prefer a simpler route, pocket screws or dowels work well, but glue surface and clamp pressure matter. Dry-fit the whole base before applying glue, check that the diagonals match, and then clamp it square.

  1. Cut mortises in all four legs, about 1/2 inch deep.
  2. Cut matching tenons on the aprons, roughly 1/2 inch long.
  3. Dry-fit the frame and check square by measuring diagonals.
  4. Glue and clamp the base, wiping excess glue before it sets.
  5. Attach the top with figure-eight fasteners or screws in elongated holes so the wood can move.

Sand, Finish and Protect the Surface

Sand progressively from 120 to 180 grit, then ease sharp edges by hand. Apply a finish that suits how the table will be used. A wiping varnish or oil-based polyurethane resists rings from drinks well. Allow each coat to dry fully and scuff lightly between coats. Woodworking techniques for sanding and finishing are worth reviewing before you start, because a rushed finish can undo good joinery.

Common Mistakes

  • Skipping the dry fit, which hides out-of-square legs until glue is already set.
  • Fastening the top rigidly to the aprons, which causes cracks as the wood expands and contracts.
  • Cutting parts to length before checking actual stock thickness.
  • Using too much glue, which prevents joints from seating and leaves squeeze-out that ruins finish.
  • Rushing the finish schedule without enough drying time.
  • Bar clamps hold the base square while glue cures, which is the most important step in the assembly. View on Amazon
  • Combination square checks each leg and apron for true 90-degree corners before you assemble. View on Amazon
  • Random orbit sander speeds up flattening the top and smoothing the aprons without leaving deep scratches. View on Amazon

If you are still deciding which tools to buy first, Woodworking Tools for Beginners: What to Buy First covers the essentials. For more joinery methods, Woodworking Techniques: Measure, Cut, Join, Sand, Finish explains the sequence in detail.

FAQ

What wood works best for an end table?

Hardwoods like oak, maple and walnut hold up well to daily wear. Pine is cheaper to work but dents more easily, so it suits lighter use.

How tall should an end table be?

Most end tables fall between 22 and 26 inches tall, which places the top near the height of a standard sofa arm.

Do I need a table saw to build this project?

No. A hand saw, a miter saw or a circular saw with a guide can produce accurate parts, though a table saw makes repeatable cuts easier.

Conclusion

With a clear cut list, careful joinery and a patient finish, a simple end table is a very achievable first project. Build the base square, leave room for the top to move, and sand thoroughly before finishing. Check your local building or workshop resources for current guidance on power tool safety before you start.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.