Updated November 2026

Fence board birdhouse plans give you a practical, low-waste way to build a sturdy nest box from a single 6-foot cedar fence board. With one board, a few screws, and basic hand or power tools, you can produce a house sized for chickadees, wrens, or bluebirds in an afternoon. This guide covers the cut list, the hole and drainage details that matter, and the assembly order.

Materials and Cut List

Start with a cedar or cypress fence picket or board at least 5/8 inch thick and about 5.5 inches wide, so the ripped sides stay stiff. Untreated cedar resists rot and avoids the chemicals that can harm nesting birds. A 6-foot board yields enough stock for the front, back, sides, floor, and roof with some waste.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • Front and back: 9 1/2 inches long, 5 1/2 inches wide, one piece each
  • Sides: 7 inches long at the back, 8 inches at the front (for a sloped roof), two pieces
  • Floor: 4 x 4 inches, with 1/4-inch drainage holes drilled through
  • Roof: 6 x 6 inches, cut from the same board or a second piece

Measurements vary by species. Chickadee houses use a 1 1/8-inch entrance hole and a 4 x 4 inch interior, while bluebird houses use a 1 1/2-inch hole and a slightly larger floor. Check the species-specific dimensions before you cut.

Cutting and Drilling Steps

  1. Rip the board to width if it is wider than 5 1/2 inches, then crosscut the pieces to length with a miter saw or hand saw.
  2. Mark the entrance hole on the front panel, about 6 to 7 inches above the floor, centered side to side. Drill a pilot hole first, then use a hole saw or spade bit to make the final opening.
  3. Drill four 1/4-inch drainage holes in the floor and two small ventilation holes near the top of each side panel.
  4. Roughen the inside faces of the front and back with a saw kerf or a few scratches so young birds can climb out. Leave the outside smooth.

Assembly and Mounting

Assemble the box with exterior-rated galvanized deck screws, not nails, because screws can be removed for annual cleaning. Pre-drill every screw hole to keep the cedar from splitting. Attach the floor first, then the sides, then the front and back. Fit the roof so it overhangs the front by about 1 inch to shed rain away from the entrance.

Mount the house on a post or tree at 5 to 10 feet high, facing away from prevailing winds and in partial shade. Use a predator guard or baffle if cats or raccoons are nearby. Many owners add a hinged or screwed-on roof so the interior can be cleaned each fall.

Common Mistakes

  • Skipping drainage holes, which lets moisture collect and leads to mold and rot.
  • Using pressure-treated lumber or painted boards, which can release harmful residues.
  • Making the entrance hole too large, which invites starlings and house sparrows.
  • Mounting the box in full sun, where the interior can overheat in summer.
  • Leaving the roof fixed with no way to open it, making annual cleaning difficult.
  • Hole saw kit with bi-metal blades: Clean, accurate entrance holes are much easier to cut with a kit that includes the right sizes. View on Amazon
  • Galvanized exterior deck screws: They resist corrosion from cedar tannins and make the box easy to take apart for cleaning. View on Amazon
  • Miter saw: Repeatable square cuts keep the box panels aligned during assembly. View on Amazon

FAQ

What wood is best for fence board birdhouse plans?

Untreated cedar is the most common choice because it resists rot without chemical treatment. Cypress and pine work too, provided they are unfinished and unpainted on the inside.

Should I paint or stain the birdhouse?

Leave the interior bare. The exterior can be given a light coat of non-toxic exterior stain or left natural, which weathers to gray over time.

When should I clean out the nest box?

Clean it once each fall after the nesting season ends, removing old nesting material and any parasites. Some species use a box for roosting in winter, so a late-fall cleaning is usually best.

Conclusion

With a single cedar fence board and the cut list above, you can build a functional nest box in one weekend. Pay close attention to hole size, drainage, and mounting height, since those choices matter most to the birds. For more size options, see Fence Picket Birdhouse Plans: Build a Cedar Birdhouse in a Weekend and Wren Birdhouse Plans Free: Build a Cedar House in One Weekend.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.