Updated November 2026

Hexagon birdhouse plans free of charge give you a six-sided nest box that is simple to cut and surprisingly sturdy. With a single 1×6 cedar board and basic tools, you can build one in an afternoon. This guide covers the cut list, the 30-degree bevel angles, and the assembly order that keeps the walls square.

Materials and Cut List

Most hexagon designs use one 6-foot cedar 1×6 or a 1×8 cut down, which is enough for the walls, roof pieces and floor. Cedar or pine resists rot, and unfinished wood keeps the interior free of paint fumes. Use exterior-grade wood screws and no glue on the inside surfaces if you want to be able to clean the box later.

Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.

  • Six side walls: 6 inches tall by 5 1/2 inches wide, each end cut at 30 degrees
  • Floor: hexagon cut from 3/4-inch stock, roughly 5 inches point to point
  • Roof: two angled panels, each about 7 inches long, hinged or screwed with a 1-inch overhang
  • Entry hole: 1 1/4-inch diameter for chickadees and wrens, placed 5 inches above the floor

Measurements vary slightly between published plans, so check any free set against the cut list above before you start.

Cutting the Hexagon Walls Accurately

The walls are the part that makes or breaks this build. Each wall must meet its neighbors at 60 degrees on the inside, which means a 30-degree bevel on both long edges. Set your miter saw or table saw to 30 degrees and make test cuts on scrap first. Cut all six walls in one session so they match.

A sled or stop block makes repeat cuts consistent. If your table saw blade is not perfectly square, the walls will not close tightly, so check that before cutting the final pieces.

Assembling the Six-Sided Box

Step-by-Step Assembly

  1. Dry-fit the six walls into a ring on a flat surface and confirm the seams close without gaps.
  2. Pre-drill each seam with a 1/8-inch bit to keep the cedar from splitting.
  3. Join walls one pair at a time with 1 1/4-inch exterior screws, starting at the bottom edge.
  4. Attach the floor by driving screws up through the bottom edge of each wall.
  5. Add the roof panels, then drill two 1/4-inch ventilation holes near the top of two opposite walls.

Leave the roof loose or hinged if you plan to clean the nest out each season. Most nest boxes need annual cleaning to prevent parasites from building up.

Mounting and Placement

Mount the box 5 to 10 feet off the ground on a fence post or tree trunk, facing away from prevailing winds. An entry hole facing east or southeast keeps the interior cooler in summer. Avoid placing it where predators like cats can reach the perch area easily.

Once your hexagon box is up, you may want to build a companion design. Our guide to Round Birdhouse Plans Free: A Step-by-Step Build for Beginners uses a similar bevel-and-ring approach, and Octagon Birdhouse Plans Free: Build One in a Weekend takes the same logic one step further.

Common Mistakes to Avoid

  • Cutting the bevels at 45 degrees instead of 30, which leaves gaps at every seam.
  • Skipping pre-drilling, which splits cedar near the screw ends.
  • Sealing the roof or walls with paint or stain on the inside.
  • Making the entry hole too large, which lets starlings and larger birds in.
  • Forgetting drainage holes in the floor, which lets water pool and rot the base.
  • A stop block or crosscut sled makes identical bevels easy to repeat. View on Amazon
  • A hole saw or spade bit set cuts clean entry holes without tearing the face. View on Amazon
  • Exterior-grade stainless or coated deck screws resist rust outdoors. View on Amazon

FAQ

Are hexagon birdhouse plans free to use for personal projects?

Most free plans are published for personal, non-commercial use. Check the source page for any usage terms before selling built birdhouses.

What size entry hole should a hexagon birdhouse have?

A 1 1/4-inch hole suits chickadees, wrens and nuthatches. Smaller holes, around 1 1/8 inches, work better for wrens alone.

Can I build a hexagon birdhouse without a table saw?

Yes. A miter saw set to 30 degrees or a hand saw with a miter box can cut the bevels, though a table saw with a sled gives the most accurate results.

Conclusion

A hexagon birdhouse is a practical weekend project once the 30-degree bevels are cut accurately. Follow the cut list, pre-drill every seam and mount the box where predators cannot easily reach it. Clean it out once a year and it can house birds for many seasons.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.