Updated November 2026
Learning how to make grooves in wood with a router takes about ten minutes of setup and a few careful passes. You will end up with a clean, flat-bottomed groove in the width and depth you need, whether you are housing a shelf or cutting a channel for a panel. The key is a stable setup, a bit that matches the groove width, and removing the material in shallow passes rather than one deep cut.
Choose the Right Bit and Setup
A straight router bit is the standard choice for grooves. Match the bit diameter to the groove width you want, and confirm the shank is the same size as your router collet. Many people use a plunge router with a fence or a straight edge clamped to the workpiece to keep the cut square.
Shopping for one? See our guide: 5 Best Wood Router Prices: How Much Is a Wood Router? 5 Picks Compared.
Before you start, check the router speed chart for your bit size. Larger bits generally need slower speeds to avoid burning and chatter. Clamp the workpiece firmly to a bench, and make sure nothing is in the path of the cutter.
Set Depth and Guide the Cut
Set the depth of cut to no more than one-third to one-half the bit diameter per pass for hardwoods. For a 1/2-inch deep groove, plan on two or three passes rather than one.
- Mark the groove edges on the workpiece with a pencil and square.
- Clamp a straight edge or fence parallel to one mark, offset by the distance from the bit’s cutting edge to the fence.
- Set the depth on the router so the bit sits about 1/16 inch above the surface.
- Turn on the router and let it reach full speed before touching the wood.
- Plunge the bit slowly into the wood at the starting point, then move the router left to right, against the rotation of the bit.
- Stop, lower the bit by a pass depth, and repeat until you reach the final depth.
Always feed against the direction the bit turns. Feeding with the rotation can pull the router out of your hands.
Make Grooves Wider Than the Bit
If your groove needs to be wider than a single bit, make a series of overlapping passes. Offset the fence by a little less than the bit diameter each time, so each pass overlaps the previous one. For a 3/4-inch groove with a 1/4-inch bit, you would make three passes at fence positions spaced about 1/4 inch apart.
Alternatively, use a dado-style bit if your groove width matches a standard bit size. This saves time and gives a cleaner bottom.
Finish the Groove Cleanly
After routing, check the groove width with a caliper or a test piece of the mating material. Light sanding of the groove walls with a sanding block removes any fuzz, but avoid rounding the edges. If the bottom has ridges from the bit, a final shallow pass at full depth will smooth it.
Checklist Before You Start
- Bit diameter matches groove width
- Router speed set for bit size and wood type
- Workpiece clamped securely
- Fence or straight edge aligned and locked
- Depth set for multiple passes
- Dust and eye protection in place
Common Mistakes
- Cutting the full depth in one pass, which causes burning and tear-out.
- Feeding the router too fast, leaving rough walls.
- Forgetting to account for the offset between the bit and fence, producing a groove in the wrong spot.
- Skipping a test cut on scrap of the same species.
- Letting the router sit in one spot while the motor runs, which can scorch the wood.
Recommended Gear
- Straight router bits in a set: A range of diameters lets you match nearly any groove width without buying bits one at a time. View on Amazon
- Plunge router with depth stop: The plunge action makes it easier to start grooves in the middle of a board. View on Amazon
- Clamp-on straight edge guide: It keeps the cut parallel and reduces drift on long grooves. View on Amazon
FAQ
Can I cut a groove with a router without a fence?
You can, but a clamped straight edge gives much more accurate results. Freehand grooves tend to wander and are hard to keep square.
How deep should each pass be?
For most hardwoods, keep each pass to about one-third to one-half the bit diameter. Softwoods can usually handle slightly deeper passes.
What direction should I move the router?
Feed the router against the rotation of the bit, which is typically left to right when you face the front of the router. This keeps the cutter pulling into the wood rather than away.
Conclusion
Routing a clean groove comes down to matching the bit to the width, setting a safe depth per pass, and feeding steadily against the bit’s rotation. Practice on scrap first, and check your fit before cutting the final piece. For a deeper look at related setups, see How to Set Up a Wood Router: A Step-by-Step Guide for Beginners and How to Cut Grooves in Wood with a Router: A Step-by-Step Guide.
