Updated November 2026
Lighthouse birdhouse plans free of charge give you a tall, tapered nest box with a lantern-style top that looks great on a fence post or porch rail. This guide walks you through the basic build: a cut list, the assembly order and the details that keep wrens, chickadees or bluebirds safe and dry. You can finish the project in a weekend with basic hand tools and a table saw or circular saw.
Choose the Right Size and Wood
Most lighthouse-style houses are built from 3/4-inch cedar, cypress or pine, because these woods resist rot and hold screws well. Plan on a body about 8 inches square at the base, tapering to about 6 inches at the top, with a total height of roughly 20 to 24 inches. Keep the entrance hole size matched to your target bird: 1-1/8 inches for chickadees and wrens, and 1-1/2 inches for bluebirds.
Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.
Cut List and Assembly Steps
Cut all parts before you drill or assemble anything. Typical dimensions for the core pieces are:
- Two front and back walls: 3/4 x 8 x 22 inches, with the top edges cut at an angle to follow the taper
- Two side walls: 3/4 x 6 x 22 inches, angled the same way
- Floor: 3/4 x 6 x 6 inches, with 1/4-inch drain holes at each corner
- Roof panels: two pieces, 3/4 x 6 x 9 inches, cut at a 30-degree bevel along one long edge
- Lantern cap: a 4 x 4 x 3 inch block with a 1-inch hole for the window opening, or a decorative lantern top you build from 3/4-inch stock
- Dry-fit the four walls and check that the taper is even all the way up.
- Glue and screw the side walls to the front and back, using exterior wood glue and 1-1/4-inch galvanized or stainless screws.
- Attach the floor so it sits 1/4 inch proud of the walls, which helps water run off.
- Install the roof panels with a 1-inch overhang on all sides and a small gap at the ridge for ventilation.
- Add the lantern cap and any decorative trim, then drill the entrance hole and mount hardware.
Finishing and Mounting Details
Leave the interior unfinished and rough-textured so young birds can climb out. Paint or stain only the exterior, and use a water-based, bird-safe finish in a light color to reduce heat buildup. Mount the house 5 to 10 feet off the ground on a post or wall, facing away from prevailing winds and afternoon sun. For wrens and chickadees, a 4-inch cavity depth is adequate; bluebirds prefer a slightly larger interior.
Common Mistakes
- Cutting the taper at the wrong angle, which leaves gaps at the roof seam.
- Using untreated plywood on the walls, which delaminates in rain.
- Drilling the entrance hole too large, letting in predators or competing species.
- Skipping drain holes, which traps moisture and encourages mold.
- Installing a perch, which gives predators and House Sparrows a place to sit.
Recommended Gear
- Exterior wood glue helps the joints stay tight through seasonal swelling. View on Amazon
- Hole saw kit gives you clean entrance holes in the sizes most songbirds need. View on Amazon
- Stainless steel exterior screws resist rust and keep the house from splitting along the grain. View on Amazon
If you want more build ideas once you have this one done, the Wren Birdhouse Plans Free: Build a Cedar House in One Weekend and Round Birdhouse Plans Free: A Step-by-Step Build for Beginners guides use similar joinery and finishing methods.
FAQ
What wood is best for a lighthouse birdhouse?
Cedar and cypress are the most popular choices because they resist rot without chemical treatments. Pine works too if you seal it well with a bird-safe finish.
How high should I mount a lighthouse birdhouse?
Mount it 5 to 10 feet off the ground, out of reach of cats and raccoons. Face the entrance away from the prevailing wind and direct afternoon sun.
Do I need a perch on the entrance hole?
No. Perches help predators and invasive House Sparrows more than the target birds, so leave them off.
Conclusion
With a single sheet of 3/4-inch cedar and a clear cut list, you can build a lighthouse birdhouse that is both attractive and functional. Check the entrance size, drill drain holes and mount the house at the right height. Consult a local wildlife or extension office if you have questions about which species are common in your area.
