Updated November 2026

Free mourning dove birdhouse plans are really plans for a platform, not an enclosed box. Mourning doves are ground-nesting birds that build flimsy stick nests, so the most useful thing you can build is a shallow, open tray with a rail to hold the nest in place. This guide gives you the dimensions, cut list, and assembly steps for a simple cedar platform you can finish in one weekend.

Why Doves Need a Platform, Not a Box

Doves do not enter cavities. They lay two white eggs on a loose platform of twigs, usually in a conifer, on a ledge, or on a flat surface. A traditional nest box will be ignored. A platform with a raised lip keeps the nest from sliding off and gives the birds a stable, open spot to sit.

Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.

Cut List and Materials

Use cedar or another rot-resistant board, and keep the platform as untreated as possible. Metric-free dimensions below use standard lumber sizes.

  • (1) 1×8 cedar board, 12 inches long, for the platform floor
  • (2) 1×2 cedar strips, 12 inches long, for the front and back rails
  • (2) 1×2 cedar strips, 8 inches long, for the side rails
  • Exterior wood screws, 1 5/8 inches long
  • Exterior wood glue
  • Stainless or galvanized nails for the rails if you prefer nailing

Step-by-Step Build

  1. Cut the floor. Crosscut the 1×8 to 12 inches. Sand the top face and the edges.
  2. Mark the rail positions. Draw a line 1/2 inch in from each edge of the platform top. The rails will sit just inside these lines and form a lip around the nest area.
  3. Attach the front and back rails. Apply glue to one long edge of each 12-inch 1×2. Set it on the marked line and drive two screws from the underside of the floor into the rail.
  4. Attach the side rails. Fit the 8-inch 1×2 strips between the front and back rails at each end. Glue and screw them into place from underneath.
  5. Check for square. Measure corner to corner. The two diagonals should match within about 1/8 inch.
  6. Drill drainage holes. Place four 1/4-inch holes in the floor so rain can drain out of the nest area.
  7. Finish. Apply a clear exterior sealer or leave the cedar bare. Let it cure fully before mounting.

Mounting Height and Location

Mount the platform 6 to 10 feet off the ground on a post, or bracket it to a sturdy fence or building wall. Pick a spot with some overhead cover, such as a conifer branch or eave, and keep it away from heavy foot traffic. Face it away from prevailing wind and direct afternoon sun.

Common Mistakes to Avoid

  • Making the rails too tall. The lip should be low so the birds can step onto the nest easily.
  • Using pressure-treated lumber. Many treatments are unsuitable for birds, so stick with cedar or untreated pine.
  • Skipping drainage holes. Standing water will rot the nest and can chill eggs.
  • Mounting in full open sun. Doves prefer partial shade, and exposed platforms overheat quickly.
  • Adding perches or roofs. Doves do not need them, and roofs can trap heat.

A few tools make this build faster and more accurate. A cordless drill driver speeds up screw driving and avoids stripped heads in cedar. View on Amazon

A combination square helps you mark the rail lines and check squareness before you drive any fasteners. View on Amazon

A stainless steel exterior screw set resists rust and will hold up better than plain steel fasteners outdoors. View on Amazon

If you want more build options, the Dove Birdhouse Plans Free: Build a Mourning Dove Platform in One Weekend guide covers an alternate layout, and Mourning Dove Birdhouse Plans: A Step-by-Step Build Guide goes deeper on mounting. For a different species, see Robin Birdhouse Plans Free: Build a Nest Box With Cut List.

FAQ

Will mourning doves really use a platform?

Yes, doves are known to nest on open platforms, especially when they have a sturdy base and some overhead cover. Enclosed boxes are usually ignored.

What size should the platform be?

A platform about 12 inches square with a low rail lip gives doves enough room to build a nest and incubate eggs comfortably.

Can I use pressure-treated wood?

It is best to avoid it. Use untreated cedar or pine and a clear finish, since treated lumber may contain chemicals that are unsafe for birds.

Conclusion

A simple cedar platform with a low rail lip is all a mourning dove needs. Build it with untreated wood, add drainage holes, and mount it in partial shade at 6 to 10 feet. Check it once in spring, and you may see a nest within a few weeks.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.