Updated November 2026
Night table woodworking plans give you a clear path from a board of lumber to a bedside table that holds a lamp, a phone and a glass of water without wobbling. This guide walks through a simple four-drawer-free design: a case with a single drawer, a shelf and four legs. You will get a cut list, the order of operations and the joinery steps that keep the table square over time.
Choose the Dimensions and Materials
Most bedside tables fall between 22 and 26 inches tall, which puts the top close to mattress height. Plan for a top about 18 by 14 inches, enough room for a lamp base and a small tray. Solid hardwood such as red oak, poplar or maple works well, and 3/4-inch stock is standard for the case sides and top.
Shopping for one? See our guide: 7 Best Table Saws for Woodworking Projects Compared (2026).
Cut List and Layout
Before you cut anything, lay out your stock and mark face sides and edges. A basic cut list for the design above looks like this:
- Top: 1 piece, 3/4 x 18 x 14 inches
- Case sides: 2 pieces, 3/4 x 22 x 14 inches
- Case top and bottom rails: 2 pieces, 3/4 x 16 1/2 x 3 inches
- Shelf: 1 piece, 3/4 x 16 1/2 x 12 inches
- Drawer front, back and sides: cut to fit your drawer opening after the case is assembled
- Legs: 4 pieces, 1 1/2 x 1 1/2 x 22 inches, if you are using solid stock
Add a 1/8-inch allowance on any dimension that will be trimmed to fit. Always verify the case dimensions against your actual boards, because lumber thickness varies.
Cut the Joinery and Assemble the Case
Dadoes cut across the case sides hold the shelf and rails securely. Cut each dado about 1/4 inch deep, using a router with a straight bit or a dado set on a table saw. Test the fit on scrap first. A snug fit with light hand pressure is the target.
- Cut dadoes in the case sides for the top rail, bottom rail and shelf.
- Dry-fit the case without glue and check that the diagonals match.
- Apply glue to the joints, assemble the case and clamp it square.
- Check the diagonal measurements again and adjust clamps until they are equal.
- Let the glue cure fully before removing clamps or adding legs.
Build the Drawer and Attach the Legs
Cut the drawer parts to fit the opening with about 1/16 inch of clearance on each side. Dovetails or rabbet-and-dado joints both work for a drawer box. Attach the legs with glue and screws or mortise-and-tenon joints, and make sure the table sits flat on a level surface before the glue sets.
Finish and Final Fit
Sand through 120, 150 and 180 grit, then wipe the surfaces with a dry cloth to remove dust. Apply a stain if desired, followed by a clear topcoat such as a wiping varnish or polyurethane. Light sanding between coats keeps the surface smooth. Attach the top with figure-eight fasteners or cleats so the solid wood can move with humidity changes.
Common Mistakes
- Skipping the dry fit, which leads to glue-ups that are out of square.
- Gluing the top directly to the case, which can crack the top as the wood expands and contracts.
- Making drawer parts too tight, so the drawer sticks in summer humidity.
- Rushing the finish before the glue has cured, which can trap moisture and cause haze.
Recommended Gear
- A quality straight router bit set makes dado cuts clean and repeatable. View on Amazon
- Bar clamps in several lengths hold the case square during glue-up. View on Amazon
- A combination square checks square and marks cut lines accurately. View on Amazon
If you are new to the tools in this build, the Woodworking Tools for Beginners: What to Buy First guide covers the essentials. For measuring and layout, see Woodworking Measuring Tools: Rules, Tapes and Squares, and for clamping during glue-up, read Woodworking Clamps and Glue-Ups: Pressure and Prep.
FAQ
What wood is best for night table woodworking plans?
Red oak, poplar and maple are common choices. Oak offers strength and visible grain, poplar is easier to cut and paint, and maple is dense and wears well.
How long does this project take?
Most builders finish a single-drawer night table over one to two weekends, depending on how much time the glue-ups and finish need to cure.
Do I need a table saw for this build?
No. A circular saw with a guide, a router and a handsaw can produce all the parts, though a table saw makes the cuts faster and more accurate.
Conclusion
With accurate cuts, strong dado joints and a finish that lets the wood breathe, this night table will hold up for years. Work slowly through the dry fit and glue-up, and the project will go smoothly. Check local building or shop safety guidance before using power tools, and consult a qualified professional if you are unsure about any step.
