Updated November 2026

Plans for a church birdhouse give you a birdhouse with a steep roof, a tall steeple, and a simple nest chamber that works for common cavity-nesting birds. This guide walks you through a build that uses a single 1×6 cedar board for most parts, with a cut list, assembly order, and the entrance and ventilation details that keep the box useful and safe for birds. Plan on a weekend project with basic tools.

Cut List and Materials for Your Church Birdhouse

Most church-style birdhouse plans use 3/4-inch rough or nominal cedar or pine. Cedar resists rot better, and it does not need paint or finish on the inside. Cut the parts below before you start assembly so you can check fit as you go.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • Floor: 1 piece, 4 1/2 x 4 1/2 inches
  • Front and back walls: 2 pieces, 5 1/2 x 8 inches (the back wall extends above the front to support the roof)
  • Side walls: 2 pieces, 4 1/2 x 8 inches, with the top edges cut at the roof pitch
  • Roof panels: 2 pieces, 5 x 7 inches, with a 45-degree edge for the ridge
  • Steeple base: 1 piece, 3 x 3 inches (glued to the roof ridge)
  • Steeple tower: 1 piece, 2 x 2 x 5 inches, tapered to a point at the top
  • Hardware: 1-1/4-inch exterior screws or galvanized nails, exterior wood glue, and one hinge or a screw-in cleanout panel

Step-by-Step Assembly

Cut the Entrance Hole and Ventilation

Mark the entrance on the front wall 6 inches down from the top edge, centered side to side. Drill a 1 1/2-inch hole for chickadee-sized birds, or a 1 1/4-inch hole for wrens. Drill two 1/4-inch ventilation holes near the top of each side wall. Drill four 1/4-inch drainage holes in the floor.

Attach the Floor and Walls

Set the floor flat on the bench. Fix the front wall to the floor with glue and two screws, keeping the bottom edges flush. Attach the side walls next, then the back wall, which should sit flush with the outer edges of the sides. Check that the box is square with a tape measure across the diagonals; the two measurements should match.

Build and Attach the Roof

Fasten the two roof panels to the top of the walls so the 45-degree edges meet at the ridge. Leave a small overhang of about 3/4 inch on the front and sides to shed rain. Glue and screw the steeple base onto the ridge, then attach the tapered tower to the base.

Add the Hinged Panel and Finish

Use a hinge or screws on one side or the front panel so you can clean the nest box each fall. Sand all exterior edges lightly. Leave the inside bare and unpainted. Apply a water-based exterior finish to the outside only if you want a painted look, and let it cure fully before mounting.

Mounting and Placement Checklist

  1. Mount the box 5 to 10 feet off the ground on a post or tree, depending on the species you want.
  2. Face the entrance away from prevailing winds and direct afternoon sun.
  3. Use a predator guard or mount on a smooth pole to reduce access by cats and raccoons.
  4. Clean out old nesting material after each season.

Common Mistakes

  • Skipping drainage holes, which lets water pool in the floor.
  • Making the entrance too large, which invites starlings and house sparrows.
  • Using treated lumber or painting the inside, both of which can harm nesting birds.
  • Fastening the roof with too few screws, so it loosens in wind.
  • Exterior wood glue holds the joints while screws set and resists moisture better than standard glue. View on Amazon
  • Hole saw or spade bit set makes clean entrance holes without splitting the face of the wall. View on Amazon
  • Stainless or galvanized exterior screws resist rust and hold up better outdoors than interior-grade fasteners. View on Amazon

FAQ

What wood is best for a church birdhouse?

Cedar is the most common choice because it resists rot and does not need chemical treatment. Untreated pine also works if you seal the outside.

How big should the entrance hole be?

Use 1 1/4 inches for wrens and 1 1/2 inches for chickadees. Larger holes allow larger birds and invasive species to take over the box.

When should I build and mount the birdhouse?

Build and mount it in late winter or early spring, before nesting season starts. Birds often choose a site early, so having the box up in time gives them the best chance to use it.

Conclusion

With the cut list above, you can build a sturdy church birdhouse in a single weekend. Keep the entrance size right, add drainage and ventilation, and mount it in a safe, sheltered spot. Clean it out each fall, and it will last for many seasons.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.