Updated November 2026

Red cedar birdhouse plans give you a nest box that resists rot, holds up to rain and stays stable for years without finish. This guide walks through a simple single-room design sized for chickadees, nuthatches and wrens, with a cut list, assembly order and the details that keep the box safe for birds. You will need one 1×6 cedar board about six feet long and a handful of basic tools.

Cut List and Materials

Use clear western red cedar, dressed to 3/4 inch thick. Rough cedar fence boards often measure closer to 5/8 inch, which still works but changes the fit. Cut the parts to these sizes:

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • Front: 1 piece, 5-1/2 in. x 9 in.
  • Back: 1 piece, 5-1/2 in. x 12 in. (extends above the roof as a mounting tab)
  • Sides: 2 pieces, 5-1/2 in. x 7-1/2 in. with a 3-degree bevel along the top edge so the roof sheds water
  • Floor: 1 piece, 4-1/2 in. x 4-1/2 in.
  • Roof: 2 pieces, 3-1/2 in. x 7 in., joined at a shallow peak

Add 1-1/4 inch exterior galvanized or stainless screws and a small amount of exterior wood glue. Avoid steel nails in cedar, since cedar tannins corrode ordinary steel fasteners over time.

Assembly Steps

  1. Drill a 1-1/8 inch entrance hole in the front board, centered 6 inches above the floor line. For chickadees, the standard 1-1/8 inch opening keeps out larger starlings.
  2. Drill four 1/4 inch drain holes in the floor and four 3/16 inch ventilation holes near the top of each side panel.
  3. Attach the floor to the front and back using glue and two screws per side, leaving the floor set back slightly from the bottom edge.
  4. Fasten the sides to the floor and front with two screws each, keeping the bevelled edges at the top.
  5. Join the roof panels at the peak with a small overlap so water runs off both sides, then screw the roof down through the top of each side.
  6. Leave the inside rough. Birds grip rough surfaces to climb out of the box, so do not sand the interior.

Finishing and Mounting Notes

Leave the cedar unfinished, or apply a single coat of water-based exterior stain on the outside only. Never paint or stain the inside, and skip any treatment that could give off fumes near nesting birds. Cedar weathers to silver-gray in a few seasons, which is fine. Mount the box on a post or fence at 5 to 10 feet high, with the entrance facing away from prevailing winds. For tips on keeping the box in good shape, see Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists for finishing comparisons across species.

Smaller Builds Using the Same Method

Once you have built this box, the same joinery works for other species. If you want a narrower entrance or a smaller interior, Plans for Wren Birdhouse: A Step-by-Step Guide With Cut List shows the adjustments for a tiny house. For a larger cavity, the approach in Tree Swallow Birdhouse Plans: A Step-by-Step Build Guide and Western Bluebird Birdhouse Plans: Build a Nest Box in One Afternoon covers the wider floor and opening sizes. Cedar fence stock is a common starting point for these projects, and Cedar Fence Picket Birdhouse Plans: Build One in a Weekend shows how to use it.

  • Forstner bit set: Clean, flat-bottomed holes make the entrance hole and drain holes come out neat. View on Amazon
  • Exterior wood screws: Coated or stainless screws resist the tannins in cedar. View on Amazon
  • Exterior wood glue: A waterproof glue keeps the joints tight through freeze and thaw cycles. View on Amazon

Common Mistakes

  • Using painted or pressure-treated lumber. Treated wood can contain compounds you do not want near nesting birds.
  • Drilling the entrance too large, which lets in starlings and house sparrows that can crowd out native species.
  • Sealing the roof seam with caulk, which traps moisture inside the box.
  • Skipping drain holes. Standing water in the floor can chill or drown a nest.
  • Mounting the box in full sun or where cats can reach the entrance.

FAQ

Is red cedar the best wood for a birdhouse?

Red cedar is one of the most common choices because it resists rot and insects without chemical treatment. It also stays cool in summer, which helps protect nesting birds.

How thick should cedar birdhouse walls be?

Three-quarter inch is the usual target. Thinner walls can crack or let in too much cold, while thicker walls add weight without much benefit.

When should I clean out an old birdhouse?

Clean the box after each nesting season, once the young have fledged and before the next breeding period begins. Remove old nesting material and check the drain holes.

Conclusion

A well-made red cedar birdhouse can last many years with minimal care. Cut the parts accurately, keep the interior rough, and mount the box where predators cannot easily reach it. Build one, then adjust the entrance size to suit the birds in your yard.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.