Updated November 2026

A riving knife table saw setup keeps the blade’s kerf open behind the cut, which is the single most effective way to prevent kickback when ripping lumber. In this guide you will learn what a riving knife does, how to align it with the blade, how to set its height, and how to check the setup before every cut. The steps apply to most contractor, hybrid and cabinet saws that come with a riving knife or accept one as an accessory.

What a Riving Knife Does

A riving knife is a thin, fixed metal fin mounted directly behind the blade. It moves up and down with the blade but not side to side. As the board passes the blade, the riving knife stays in the kerf and keeps the wood from pinching the back of the blade. Pinching is what causes most kickback, so the riving knife addresses the root cause rather than just catching the workpiece after the fact.

Shopping for one? See our guide: Harbor Freight Tools Table Saw: 6 Best Picks Compared (2026).

Many saw manufacturers now include a riving knife as standard equipment, and some older saws use a splitter or a blade guard instead. A splitter is fixed and does not move with the blade, which limits its use for angled cuts. Check your saw’s manual to confirm which system you have before you start.

Setting Up the Riving Knife Correctly

Proper alignment matters more than almost any other part of the setup. A riving knife that sits off-center can rub the blade or fail to keep the kerf open.

  1. Unplug the saw. Remove the throat plate and the blade guard assembly.
  2. Raise the blade to its maximum height, then loosen the riving knife’s mounting bolt or lock.
  3. Align the riving knife so its edge sits in the same plane as the blade, with the gap between the knife and the blade body about 1/8 inch or less at the top of the teeth. Consult your manufacturer’s specifications for the exact tolerance.
  4. Tighten the lock, then rotate the blade by hand to confirm it does not contact the knife at any point.
  5. Lower the blade and check that the knife height is set so its top sits just below the highest tooth at full blade height.
  6. Replace the throat plate and guard, then reconnect power.

Checking Alignment and Height

Recheck the riving knife after changing blades, moving the saw, or any time the blade has been removed. A quick check with a straightedge or a dial indicator will show whether the knife sits parallel to the blade. Small misalignments are common after blade swaps, so this habit takes less than a minute and prevents problems later.

The riving knife also needs to match the blade. A thin-kerf blade may require a different knife than a full-kerf blade, so confirm your knife thickness is correct for the blade you are using. Dado stacks usually require the riving knife to be removed entirely, which is a point many owners overlook.

Using the Riving Knife on Common Cuts

Ripping is where the riving knife does its most important work. Keep the board firmly against the rip fence, use a push stick when the workpiece gets narrow, and never stand directly behind the blade. For crosscuts using a sled or miter gauge, the riving knife stays in place and does not interfere, though some operators choose to lower the blade height for these cuts.

Angled cuts, such as bevel rips, are where many people run into trouble. Some saws allow the riving knife to tilt with the blade and some do not, so consult your saw’s documentation before making bevel cuts with the knife in place. If the knife must be removed for a particular cut, do so only with the blade stopped and the saw unplugged, and reinstall it before resuming normal work.

Common Mistakes

  • Running the saw with the riving knife removed or misaligned, which removes the kickback protection entirely.
  • Setting the knife too high, which can leave the blade’s back teeth exposed and increase injury risk.
  • Forgetting to recheck alignment after a blade change or after the saw has been bumped or moved.
  • Using a knife that is too thick for a thin-kerf blade, which can cause binding.
  • Trying to rip narrow stock without a push stick, which brings your hands close to the blade.

A straightedge and a set of feeler gauges make alignment checks faster and more accurate than eyeballing the gap. A pair of push sticks keeps your hands clear of the blade during narrow rips. Replacement riving knives matched to your saw’s model are often available as direct-fit accessories if the original is lost or damaged.

Look for a straightedge with a machined edge and a feeler gauge set in thousandths of an inch. Check that any push stick you buy has a grip that keeps your hand well above the blade line. View on Amazon View on Amazon View on Amazon

FAQ

Is a riving knife required on a table saw?

Many modern saws include one as standard, and it is strongly recommended for ripping. Check your saw’s manual, since some models use a splitter or guard instead.

How close should the riving knife be to the blade?

The gap should be very small, typically about 1/8 inch or less, and the knife should be parallel to the blade. Confirm the exact tolerance in your manufacturer’s specifications.

Can I remove the riving knife for dado cuts?

Yes, dado stacks usually require removing the riving knife. Reinstall it once you return to standard blade work.

Conclusion

A correctly aligned riving knife keeps the kerf open and greatly reduces kickback risk during ripping. Check alignment after every blade change and keep the knife at the proper height. For more setup ideas and saw stand builds, browse the related guides on this site.

Always consult your saw manufacturer’s manual for specific safety and setup requirements, and consider a qualified professional if you are unsure about any adjustment.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.