Updated November 2026
Rock city birdhouse plans describe a simple, weather-resistant nest box built from a handful of flat boards and a sloped roof. Following them, you will end up with a birdhouse that suits cavity-nesting songbirds, can be built in an afternoon, and stands up to rain when the joints are glued and the seams are sealed. The steps below cover materials, the cut list, assembly, and finishing.
Materials and Cut List
Use rough or smooth 3/4-inch cedar, pine, or another untreated softwood. Avoid pressure-treated lumber, since the chemicals can harm birds. The design uses five main pieces plus a roof panel:
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
- Two front and back panels: 5-1/2 in. wide x 9 in. long
- Two side panels: 4 in. wide x 9 in. long, with the top edges angled to match the roof slope
- One floor: 4 in. x 4 in.
- One roof panel: 6 in. x 7 in.
Cut the sides to produce a 4-inch-deep interior. Mark the front panel 7 in. from the bottom for the entry hole location, but do not drill it yet.
Assembling the Box
Attach the Floor and Sides
Lay the floor on your bench and set one side panel flush with one edge. Drive two 1-1/4-inch exterior screws through the side into the floor edge, pre-drilling to avoid splitting. Attach the second side the same way, then fasten the back panel across the rear edges.
Add the Front and Roof
Attach the front panel last, leaving it free at the top so you can open the box for cleaning. Use a hinge or a single screw at the top and a removable wooden peg or latch at the bottom. Center the roof panel so it overhangs the front by about 1 inch, then fasten it with stainless or galvanized screws.
Drilling the Entry Hole and Ventilation
Drill a 1-1/2-inch entry hole for wrens, chickadees, and similar small species, measured from the top of the hole to the floor of the box, about 6 inches above the floor. Drill four 1/4-inch ventilation holes near the top of the side panels and a few 1/4-inch drainage holes in the floor. Sanding the inside of the entry hole is worth doing so the birds can grip it.
Finishing and Placement
Leave the interior unfinished and unpainted so birds and moisture cannot be trapped by chemicals. Apply two coats of exterior, bird-safe finish or a light stain to the outside, letting each coat dry fully. Mount the box 5 to 10 feet off the ground on a post or tree, facing away from prevailing winds and afternoon sun.
Common Mistakes
- Making the entry hole too large, which lets predators like starlings or squirrels reach the nest.
- Skipping drainage holes, which allows water to pool and rot the floor.
- Using treated lumber or painting the interior.
- Fastening the roof too tightly, which makes annual cleaning difficult.
- Mounting the box in full sun, where the interior can overheat.
Recommended Gear
- Pre-drilling bit set: prevents splitting near the screw ends of thin cedar boards. View on Amazon
- Exterior wood screws, stainless: resist rust and staining from cedar tannins over multiple seasons. View on Amazon
- Hole saw kit for wood: cuts a clean, round entry hole with fewer tear-out problems than a spade bit. View on Amazon
FAQ
What size entry hole should I use for these plans?
A 1-1/2-inch hole suits wrens, chickadees, and titmice. Larger holes invite starlings and house sparrows, which can displace native species.
Can I use pressure-treated wood for a rock city birdhouse?
No. Chemicals in pressure-treated lumber can harm nesting birds and their young. Stick with untreated cedar or pine.
When should I clean out the birdhouse?
Clean it once after each nesting season, ideally in fall or early winter, removing old nesting material and checking for parasites. If you are unsure about local nesting regulations or species protections, consult your state wildlife agency.
Conclusion
With a basic cut list, careful hole sizing, and a bird-safe finish, these rock city birdhouse plans produce a durable nest box in one afternoon. Mount it at the right height and clean it each year, and it can host nesting birds for many seasons. Check the related builds below if you want to try a different design next.
Related reading
- Wren Birdhouse Plans PDF: A Step-by-Step Build With Cut List
- Wren Birdhouse Plans Free: Build a Cedar House in One Weekend
- Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists
- Wine Cork Birdhouse Plans: A Step-by-Step Build for Beginners
- Whimsical Birdhouse Plans Free: 5 Playful Builds With Cut Lists
- Western Bluebird Birdhouse Plans: Build a Nest Box in One Afternoon
