Updated November 2026
Buying second hand woodworking tools can get you a solid shop for far less than new, but only if you know what to look for. This guide walks you through inspecting used tools, deciding which ones are worth buying secondhand, and avoiding the common traps. By the end, you will know how to judge a used saw, plane, or router before you hand over any money.
Decide Which Tools Are Worth Buying Used
Some tools age well and some do not. Hand tools with cast iron bodies, such as bench planes, chisels with intact handles, and marking gauges, are usually good used buys because their mechanisms are simple and easy to restore. Power tools are more of a gamble. Motors, switches, and electronic controls can fail in ways that are hard to spot on a quick look. Check our guide to Hand Tools for Woodworking: Uses, Safety and Sharpening and Woodworking Power Tools: What Each Does and Safety Basics to see how each category works before you shop.
Shopping for one? See our guide: 6 Best Wood Router Hand Tools for Every Shop (2026).
Inspect Each Tool Before You Buy
Take your time with each tool and check the following points in order.
- Cracks and damage: Look closely at castings, especially near bolt holes and handles. A hairline crack in cast iron usually means the piece is ruined.
- Flatness: Lay a known straightedge across the sole of a plane or the table of a saw. Hold it to the light to check for gaps.
- Moving parts: Open and close adjustment mechanisms, tighten and loosen locks, and confirm nothing binds or wobbles.
- Blade or cutting edge condition: Pitting, heavy rust, or chips in a blade often cost more to fix than the tool is worth.
- Electrical checks on power tools: Ask to plug the tool in and run it. Listen for grinding, watch for sparks at the brushes, and confirm the switch works smoothly.
Check Rust, Wear, and Restorability
Surface rust on cast iron is often removable with fine abrasive pads and a little penetrating oil, and many experienced woodworkers prefer tools in this condition because they can clean them to a like-new finish. Deep pitting is harder to fix and may leave a flat surface uneven. Pay attention to the difference between surface rust and structural damage. A tool with a rough but sound sole can be flattened, while a tool with a cracked body or missing parts is usually not worth the effort.
| Tool type | Good used candidate? | Main thing to check |
|---|---|---|
| Bench planes | Yes | Sole flatness and cracks |
| Chisels | Yes | Handle condition and blade edge |
| Table saws | Sometimes | Motor, arbor play, and blade guard |
| Routers | Sometimes | Collet wear and plunge action |
| Sanders | Caution | Pad condition and dust port |
Know Where to Look and What to Avoid
Estate sales, auctions, online classifieds, and retiring woodworkers’ shops all turn up good used tools. Ask questions about how the tool was stored and used, and never buy a power tool with a damaged cord or a missing guard. For larger tools, plan how you will transport them, and confirm whether you can test the tool before purchase. If you are unsure about electrical safety on a used power tool, have a qualified electrician or the manufacturer check it before use.
Common Mistakes
- Buying a power tool you have never seen running.
- Overlooking warped or cracked cast iron bodies.
- Assuming every rusty tool is ruined. Surface rust is often fixable.
- Skipping safety guards or accessories that the tool needs to operate safely.
- Forgetting that blades and bits may cost more to replace than the tool itself.
Recommended gear
A few basic supplies make it much easier to inspect and restore used tools.
- Precision straightedge: Lets you check flatness on planes, saw tables, and jointer beds during your inspection. View on Amazon
- Fine abrasive pads and penetrating oil: Removes surface rust from cast iron without damaging the surface. View on Amazon
- Digital calipers: Measure blade thickness, arbor size, and collet diameter so you know whether replacement parts will fit. View on Amazon
FAQ
Are second hand woodworking tools safe to use?
Many are, provided they are structurally sound, have intact guards, and have working electrical components. Inspect carefully and have any questionable power tool checked before use.
Which tools are the best to buy used?
Hand planes, chisels, and marking tools are usually the safest bets because they are mechanically simple and easy to restore. Power tools carry more risk and need a careful test run.
Can rust ruin a used tool?
Surface rust is often removable. Deep pitting, cracks in the casting, or a severely warped surface usually mean the tool is not worth restoring.
Conclusion
Second hand woodworking tools can save money and give you quality equipment, but only if you inspect each one thoroughly. Focus first on hand tools with sound castings, and be cautious with power tools until you have tested them. Once you have your basics, pair your used gear with a simple project such as a Woodworking Plans for Shelves: A Step-by-Step Build Guide to put your new shop to work.
