Updated November 2026

Simple birdhouse plans PDF files give you a cut list, a dimensioned drawing, and assembly steps you can print and take to the shop. This guide explains what a good plan should include, walks through the build, and lists the mistakes that most often cause a birdhouse to fail. By the end, you will know how to check any printable plan before you cut a single board.

What a Good Simple Birdhouse Plan Should Include

Not every free PDF is worth printing. A useful plan lists every part with its exact dimensions, the species and thickness of the lumber, and the hole size for the target bird. Manufacturers and bird-conservation groups commonly recommend a 1-1/8 to 1-1/2 inch entrance for small cavity nesters such as wrens and chickadees, with 1-1/2 inch used for bluebirds and 1-1/4 inch for titmice. If a plan does not state the entrance diameter, skip it.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

Look for these items in any printable plan:

  • A cut list with part names, quantities, and finished dimensions
  • A drawing with a scale or labeled measurements
  • Fastener type and placement
  • Drainage holes, ventilation, and a way to open the front or roof for cleaning

Materials and Tools You Need

Most simple designs use one 1×6 board about 6 feet long, which yields enough stock for the front, back, sides, floor, and roof. Choose rough-sawn cedar or pine with no paint, stain, or pressure treatment. Exterior-grade plywood also works for the back and roof. Use galvanized or stainless exterior screws or 1-1/4 inch galvanized nails.

Gather these tools before you start:

  1. Tape measure and combination square
  2. Circular saw or miter saw
  3. Drill with a 1/16 inch pilot bit and a spade or Forstner bit for the entrance
  4. Screwdriver or drill driver and clamps
  5. Sandpaper (120 grit) for smoothing the entrance edge

Step-by-Step Build From the Cut List

Cut all parts to the dimensions on your plan, then label each piece on its inside face with a pencil. Labeling saves you from mixing up the front and back, which look nearly identical.

Assemble the Box

  1. Attach the floor between the two side panels, keeping the bottom edges flush.
  2. Fasten the back panel to the sides and floor, using two screws per joint.
  3. Add the front panel last, leaving it unattached if your design uses a removable front for cleaning.

Add the Roof and Entrance

  1. Attach the roof with hinges or screws. A hinged roof makes annual cleaning far easier.
  2. Drill the entrance hole, centering it about 6 to 8 inches above the floor. Sand the edges so they are smooth, which protects nestlings from scrapes.
  3. Drill four 1/4 inch drainage holes in the floor and two small ventilation holes near the top of the sides.

How to Mount Your Birdhouse Safely

Mount the box where predators have difficulty reaching it. Many guides recommend a pole or post at least 5 feet off the ground, with a predator guard. Face the entrance away from prevailing winds and direct afternoon sun. Clean the box after each nesting season to remove old material and parasites.

Common Mistakes

  • Using treated lumber or painted boards, which can harm birds.
  • Drilling an entrance that is too large, inviting starlings or house sparrows.
  • Skipping drainage holes, which lets moisture build up and chill the nest.
  • Mounting the box in full sun, where temperatures inside can climb dangerously high.
  • Forgetting to make the box easy to open, so it never gets cleaned.
  • Exterior screws hold joints well without splitting thin cedar. View on Amazon
  • A Forstner bit set produces clean, accurate entrance holes. View on Amazon
  • A combination square makes it easy to check square corners during assembly. View on Amazon

Where to Find More Designs

Once you have built a basic box, you can compare other layouts. The Free Birdhouse Plans PDF: 6 Printable Designs With Cut Lists collection gives you several options at similar skill levels. If you want a specific species, Wren Birdhouse Plans Free: Build a Cedar House in One Weekend and Western Bluebird Birdhouse Plans: Build a Nest Box in One Afternoon list entrance sizes and dimensions for those birds. For a quick project with scrap wood, Popsicle Stick Birdhouse Plans: A Step-by-Step Build for Beginners is a useful starting point.

FAQ

What size should a simple birdhouse be?

Most small songbird houses have a floor of about 4 by 4 inches and an interior height of 8 to 10 inches. Always confirm dimensions against the species you want to attract.

Can I print a birdhouse plan on regular paper?

Yes. Print at 100 percent scale and check that a measured line on the printout matches the dimension printed beside it. Adjust your print settings if the drawing has been resized.

Do birdhouses need a perch?

No. Perches help predators and often encourage house sparrows and starlings, so most cavity-nester guidelines recommend leaving them off.

Conclusion

A simple birdhouse plan PDF is only as good as its cut list and entrance measurement, so check both before you cut. Build with untreated lumber, drill the correct hole size, and mount the box where it stays safe and cool. Clean it every year and your birdhouse can last for seasons.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.