Updated November 2026

Two story birdhouse plans give you a nest box with two separate compartments stacked one above the other, so two pairs of birds can nest on the same pole. This guide walks you through a simple cedar design, a cut list, and the assembly steps. You will finish with a sturdy house that works for small cavity nesters like chickadees, wrens, and nuthatches.

Choose the Right Size and Entry Holes

Before you cut anything, decide which birds you want to attract, because the entry hole sets the species. A 1-1/8 inch hole suits chickadees and titmice, while a 1-1/2 inch hole is standard for bluebirds. Keep both floors at least 6 inches apart so the upper and lower households do not disturb each other. The design below uses 1-1/8 inch holes on both floors.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

Cut List and Materials

Use 3/4 inch cedar or pine with the rough side facing inward. Cedar resists rot without paint, and it is the material most builders choose for outdoor nest boxes. Cut the following pieces:

  • 2 side panels: 6 in. x 16 in.
  • 2 front/back panels: 5-1/2 in. x 16 in. (front gets the entry holes)
  • 2 floors: 5 in. x 5 in. (one drilled for drainage)
  • 1 middle divider: 5 in. x 5 in.
  • 1 roof: 7 in. x 9 in., cut with a slight slope
  • 1 front ledge: 1 in. x 6 in. scrap piece

Assembly Steps

  1. Drill two 1-1/8 inch entry holes in the front panel, one about 6 inches from the top and one about 13 inches from the top. Center each hole horizontally.
  2. Drill four 1/4 inch drainage holes in each floor and three 3/8 inch ventilation holes near the top of each side panel.
  3. Attach the middle divider between the side panels, about 6 inches from the bottom, using exterior wood glue and 1-1/4 inch exterior screws.
  4. Join the front and back panels to the sides with glue and screws. Keep the top edges flush so the roof sits level.
  5. Fasten the floors at the bottom of each compartment. Add the front ledge below the lower entry hole only, to help fledglings climb out.
  6. Attach the roof with hinges or screws so you can open the house for annual cleaning.

Sanding and Finishing

Sand interior edges lightly, but leave the inside surfaces rough so young birds can grip the walls. Apply an exterior finish only to the outside, and let it dry fully before mounting. Do not use stains or paints on the inside.

Common Mistakes

  • Making the entry holes too large, which lets predators like starlings enter.
  • Sealing the floor completely, which traps water. Always drill drainage holes.
  • Painting the interior, which can harm nesting birds.
  • Mounting the house in direct afternoon sun, which can overheat the nest.
  • Skipping annual cleaning, which leaves parasites from earlier nests behind.
  • Forstner bit set: Gives clean, flat-bottomed entry holes that do not split the front panel. View on Amazon
  • Exterior wood glue: Holds the joints while the screws pull them tight, and stays flexible outdoors. View on Amazon
  • Corrosion-resistant exterior screws: Prevent staining and rust streaks on cedar over several seasons. View on Amazon

FAQ

Where should I mount a two story birdhouse?

Mount it on a pole 5 to 10 feet off the ground, facing away from prevailing winds and away from heavy afternoon sun. Clear open space within about 30 feet helps adult birds watch for danger.

Can two different bird species use the same house?

Yes, if their entry hole sizes match, but the two compartments may not be used by the same species. Small holes usually attract chickadees and wrens, while larger holes draw bluebirds.

When should I clean the birdhouse?

Clean it once a year after the nesting season ends, usually in late summer or early fall. Remove old nesting material and scrub the floors with a mild soap solution, then rinse and let dry completely.

Conclusion

A two story birdhouse is a practical build that can support two nesting pairs on one pole. Match your entry holes to the species you want, drill proper drainage, and keep the interior unfinished. With the cut list and steps above, you can complete the project in a single weekend.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.