Updated November 2026

Woodworking bathroom cabinet plans give you a clear path to a vanity cabinet that fits your wall, holds up to steam and splashes, and looks like it belongs in the room. In this guide you will settle on dimensions, build a cut list, choose joinery that resists swelling, and finish the cabinet so it lasts. The build suits a single-sink vanity of about 24 to 36 inches wide.

Step 1: Measure the space and set the dimensions

Start with the wall, not the wood. Measure the width between the wall and any obstacles, then check the height from the floor to the underside of the countertop, which is usually 32 to 36 inches. Standard vanity depth is about 21 inches, leaving room for the sink bowl and plumbing behind the doors. Sketch the layout with the door sizes and drawer heights before you buy material. For more on accurate marking, see Woodworking Measuring Tools: Rules, Tapes and Squares.

Shopping for one? See our guide: 7 Best Fixed Base Wood Routers for Woodworking in 2026.

Step 2: Choose materials that handle humidity

Solid wood cabinets warp in humid bathrooms, so most builders use plywood or moisture-resistant panels for the carcass. Marine-grade plywood or a quality birch plywood holds screws and joints well. Solid hardwood works for face frames and doors, as long as you allow for seasonal movement. Avoid particleboard in wet areas, because it swells at the edges when it gets damp.

Step 3: Build the carcass with reliable joinery

Cut the side, top, bottom and shelf pieces to your cut list, then join them with dadoes, rabbets or pocket screws. Dadoes give the strongest support for shelves and the bottom panel. Dry-fit every joint, check the diagonals for square, and use clamps while the glue sets. Clamp-up habits matter here, so review Woodworking Clamps and Glue-Ups: Pressure and Prep before you glue.

Cut list checklist

  • Two sides, each cut to the full cabinet height and depth
  • One top and one bottom, sized to fit between the sides
  • One or two adjustable shelves, sized to leave a clearance gap
  • A back panel, usually 1/4-inch plywood, set into a rabbet
  • Face frame stiles and rails from solid hardwood
  • Doors and drawer fronts cut to your reveal and overlay plan

Step 4: Add doors, drawers and hardware

Mount the face frame, then hang doors using full-overlay or inset hinges, depending on your style. Drawers need slides rated for the weight you plan to store. Drill hinge and pull locations from a template so every door lines up. Test each door and drawer as you go, since a small misalignment becomes obvious on a vanity.

Step 5: Seal and finish for wet conditions

Sand to 150 or 180 grit, remove the dust, and apply a finish that resists water. Water-based polyurethane or a marine varnish works well on exposed surfaces. Seal the interior and the bottom edges too, since moisture reaches those first. Give each coat time to dry and lightly sand between coats. Good sanding technique is covered in Woodworking Techniques: Measure, Cut, Join, Sand, Finish.

Step 6: Install the cabinet level and secure

Fasten a cleat or ledger to the wall studs, set the cabinet on it, and check level in both directions. Secure the cabinet to the wall through the back rail, then connect the top and sink according to the plumbing manufacturer’s instructions. Leave a small gap at the walls for drainage and easy cleaning.

Common mistakes

  • Using untreated solid wood for the carcass, which can warp or split in a bathroom
  • Skipping the sealing step on the back and bottom surfaces
  • Cutting the cabinet to the exact wall width, leaving no room for shims or plumbing
  • Gluing up without dry-fitting, which leaves no room to correct errors
  • Ignoring power tool safety on the table saw and router during cuts

A reliable circular saw or track saw makes long plywood cuts accurate, which keeps cabinet sides square. View on Amazon

A router with a dado bit cuts clean shelf and bottom grooves. View on Amazon

Bar clamps hold the carcass square during glue-up. View on Amazon

FAQ

What wood is best for a bathroom cabinet?

Marine-grade or moisture-resistant plywood works best for the carcass because it resists swelling. Solid hardwood suits doors and face frames when you finish it well.

How deep should a bathroom vanity be?

Most vanities run about 21 inches deep, which fits standard sinks and plumbing. Measure your sink and check local code clearances before you finalize the depth.

Do I need a special finish for a bathroom cabinet?

Yes, use a water-resistant finish such as water-based polyurethane or marine varnish, and seal the interior too. Check the product label for the recommended number of coats.

Conclusion

Following these woodworking bathroom cabinet plans gives you a vanity that fits the room and handles moisture. Measure carefully, choose stable materials, and seal every surface. Check local plumbing and building requirements before installing a sink.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.