Updated November 2026

Routing letters in wood is a reliable way to make signs, name plaques and decorative lettering. To router letters in wood cleanly, you need a suitable bit, a firm template or guide, and a series of shallow passes rather than one deep cut. This guide walks through setup, cutting technique and finishing so your letters come out sharp and evenly spaced.

Choose the Right Bit and Stock

For most sign work, a straight bit between 1/4 inch and 1/2 inch in diameter gives a clean floor and crisp walls. A V-bit creates a chiseled, carved look, while a round-nose bit produces softer, rounded letter bottoms. Hardwoods like oak, maple or cherry hold detail well, while soft pine tends to fuzz and tear out. If you are cutting into a large workpiece, check the bit’s maximum cutting depth before you start.

Shopping for one? See our guide: 5 Best Wood Router Prices: How Much Is a Wood Router? 5 Picks Compared.

Plan the letter height first. Letters that are at least 2 inches tall are easier to route accurately and leave room for mistakes. Sketch the layout on the board, then mark the baseline and centerline so you can keep each word aligned.

Set Up Your Template and Router

Most beginners use a stencil or template to guide the router base. Stencil letters can be bought ready-made or cut from 1/4-inch plywood or MDF with a jigsaw and sanded smooth. The template must be exactly the size and spacing you want, because the bit’s edge follows the template’s inside or outside edge depending on your guide bushing.

Clamp the workpiece flat to the bench, and clamp the template firmly on top. Check that the router base can slide freely around the template opening without binding. Set the router to a shallow depth, usually 1/8 inch per pass, and make sure the collet is tight on the bit shank.

Routing the Letters: Step by Step

  1. Set the cutting depth to about 1/8 inch for the first pass.
  2. Start the router before the bit touches the wood, then lower it into the template opening.
  3. Move the router clockwise around the inside edge of each letter (or counterclockwise, depending on bit rotation), keeping the base pressed against the template.
  4. Make a full pass around each letter, then lift the bit out and let it stop completely before removing it.
  5. Increase depth by about 1/8 inch and repeat until you reach the final depth, usually 1/4 inch to 1/2 inch for signs.
  6. Clean out any remaining corners with a chisel or a small detail bit.

Feed speed matters. Move steadily, not so fast that the router bogs down, and not so slow that the bit burns the wood. Take lighter passes in dense hardwood and watch for scorch marks.

Finishing and Cleanup

Once the letters are routed, sand the floors lightly with 150-grit or 180-grit paper to remove fuzz. Avoid sanding the edges too aggressively, since that rounds the crisp profile you worked to create. Paint or stain can be applied into the recesses, and wiping off excess before it dries keeps the background clean.

If you are interested in more advanced routing projects, the article on How to Router Words Into Wood: A Step-by-Step Guide for Beginners covers layout ideas for multi-word signs. For decorative edge work, How to Bevel Wood with a Router: 7 Best Picks Compared for 2026 explains setup for chamfers and bevels.

Common Mistakes

  • Cutting full depth in one pass, which causes burning, chatter and bit breakage.
  • Letting the template shift during the cut, which distorts the letter shape.
  • Using a dull bit, which tears the grain instead of cutting cleanly.
  • Skipping a test cut on scrap wood to confirm depth and spacing.
  • Routing against the bit’s rotation direction, which can kick the router back.

A stable router base and a set of guide bushings make template routing much more predictable. Look for a bushing set sized to match your router base and bit diameter.

  • Guide bushing kit for template routing: helps keep the cutter centered in the template opening. View on Amazon
  • Straight router bit set in 1/4 inch shank: gives you a range of diameters for different letter sizes and stroke widths. View on Amazon

FAQ

What size router bit is best for carving letters?

A straight bit between 1/4 inch and 1/2 inch in diameter works well for most lettering. Choose a larger bit for bold letters and a smaller one for fine detail.

How deep should I rout letters in wood?

Most sign letters are routed between 1/4 inch and 1/2 inch deep. Make several passes of about 1/8 inch each rather than cutting the full depth at once.

Can I rout letters without a template?

Freehand routing is possible but hard to keep consistent. A template or CNC program gives far more uniform results, especially for repeated letters.

Conclusion

To router letters in wood well, match your bit to the letter size, use a sturdy template, and cut in shallow passes. Test on scrap first, keep the router moving steadily, and finish with light sanding. With practice, your lettering will look sharp and consistent.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.