Updated November 2026
Northern flicker birdhouse plans call for a larger, deeper nest box than most songbird houses, because flickers are big woodpeckers that excavate their own cavities in dead or dying trees. This guide gives you the key dimensions, a cut list, and the build steps to make a box flickers will actually use. Plan on a weekend project with basic hand and power tools.
Know the Dimensions Flickers Need
Flickers are among the largest woodpeckers in North America, so the box has to be scaled up. Most plans for this species use an interior floor of about 7 x 7 inches, a cavity depth of 16 to 18 inches, and an entrance hole of roughly 2.5 inches in diameter. A smaller hole keeps out European starlings and squirrels, but it must still be large enough for an adult flicker to slip through. Mount the box 6 to 20 feet off the ground, facing away from prevailing winds.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
Cut the Panels and Assemble the Box
Use rough-sawn cedar, pine or cypress at least 3/4 inch thick. Thinner stock cracks and loses insulation. Cut the following pieces:
- Front and back: 1 each, 7 x 22 inches (back extends above the roof line for mounting)
- Sides: 2 each, 7 x 16 inches with a 3-inch slope cut on the top edge
- Floor: 1 piece, 7 x 7 inches, with 1/4-inch drainage holes drilled in each corner
- Roof: 2 pieces, 9 x 9 inches, overlapping at the peak
Join the sides to the floor with exterior screws, then attach the front and back. Pre-drill every screw hole to prevent splitting, and leave the front panel removable for annual cleaning.
Add the Entrance, Ventilation and Mounting Details
Drill the entrance hole on the front panel, about 6 inches below the roof line, so the opening sits above the floor and the box stays dry. Drill two 3/4-inch ventilation holes near the top of the side panels. Roughen the inside of the front panel, or screw short wood strips to it, so chicks can climb to the hole. Attach a hinge or cleat on the back panel for mounting to a post or tree trunk.
Finish the Exterior Safely
Leave the interior bare. Paint or stain only the outside, using a low-VOC exterior finish in a neutral color. Let it cure fully before installation, since fresh finish fumes can linger inside a closed box.
Tools and Supplies Checklist
- Circular saw or miter saw and a straightedge guide
- Drill with 2.5-inch hole saw bit and 1/4-inch bit
- Exterior wood screws, 1 1/4 to 1 5/8 inches
- Tape measure, square and pencil
- Exterior-grade wood glue (optional, for extra joint strength)
- Galvanized mounting hardware
Common Mistakes to Avoid
- Building the box too small. Flickers need depth and floor space, so do not shrink the standard dimensions.
- Skipping drainage holes. Trapped moisture rots the floor and invites mites.
- Using treated lumber or painting the interior. Chemicals and fumes can harm nesting birds.
- Mounting too low or in full sun, which causes overheating.
- Forgetting annual cleaning. Remove old nesting material after the season to reduce parasites.
Recommended Gear
- Hole saw kit with a 2 1/2-inch bit: makes a clean, accurate entrance that matches the plan size. View on Amazon
- Exterior wood screws: resist rust and hold up to weather cycling better than drywall screws. View on Amazon
- Low-VOC exterior stain: gives weather protection without fumes that can affect birds. View on Amazon
Related Plans to Explore
If you want to compare sizes, the Pileated Woodpecker Birdhouse Plans: A Step-by-Step Build Guide uses a similarly deep cavity for another large woodpecker. For smaller cavity nesters, see Wren Birdhouse Plans Free: Build a Cedar House in One Weekend and Red Headed Woodpecker Birdhouse Plans Free: 5-Step Build Guide.
FAQ
What size entrance hole do northern flickers need?
Most plans use an entrance of about 2.5 inches in diameter. That is large enough for an adult flicker but still helps exclude starlings.
How high should a flicker birdhouse be mounted?
Mount it roughly 6 to 20 feet off the ground, on a post or tree trunk, with the entrance facing away from prevailing winds.
Do flickers use the same box every year?
They often nest in the same general area, but they may excavate new cavities. Clean out old material each fall so the box stays healthy for the next season.
Conclusion
With the right depth, entrance size and drainage, a northern flicker box is a straightforward weekend build. Stick to the dimensions, avoid treated wood and interior finishes, and clean the box each year. Your flickers will have a safe, sturdy place to nest.
