Updated November 2026

Church birdhouse plans free of charge are easy to find, and a steeple-style house is one of the most satisfying builds for a weekend workshop. This guide gives you a simple cut list, the key dimensions that keep birds safe and comfortable, and the assembly steps for a basic church design. By the end, you will have a sturdy, weather-tight birdhouse that looks like a tiny chapel and works as a nest box.

Choose the Right Size and Entry Hole

The entry hole determines which birds will use the house. For wrens, use a 1-1/8 inch hole. For chickadees, use 1-1/8 inch. For bluebirds, use 1-1/2 inch. A church design works well as a small songbird house, so stick to the 1-1/8 inch size unless you are targeting a specific species.

Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.

Plan the interior at roughly 4 inches wide, 4 inches deep and 8 to 10 inches tall from floor to roof peak. That gives a nest cavity large enough for a clutch without leaving too much empty space for predators to exploit.

Cut List and Materials

Use 3/4 inch cedar, rough-sawn pine or another rot-resistant board with no chemical treatment. Pressure-treated wood contains preservatives that can harm birds. The cut list for a basic church birdhouse is:

Part Quantity Dimensions (inches)
Front and back walls 2 5-1/2 x 9
Side walls 2 4 x 9
Floor 1 4 x 4
Roof panels 2 4 x 6
Steeple (bell tower) block 1 3 x 3 x 4
Steeple cap 1 3 x 3 x 1

Cut the front wall with the entry hole and the steeple cut-outs before assembly. Drill the hole with a Forstner bit or hole saw so the edge stays clean.

Assemble the Birdhouse Step by Step

  1. Drill the 1-1/8 inch entry hole in the front wall, centered about 6 inches from the bottom.
  2. Attach the floor to the side walls with exterior wood glue and two 1-1/4 inch galvanized or stainless screws per side.
  3. Join the front and back walls to the sides, keeping all edges flush.
  4. Drill four to six 1/4 inch drainage holes in the floor and two ventilation holes near the top of the side walls.
  5. Assemble the steeple block and cap, then fasten it to the roof peak.
  6. Attach the roof panels with a slight overhang of about 1 inch on each side to shed rain.
  7. Add a hinged or screwed-on roof panel so you can clean the box after nesting season.

Finish, Mount and Maintain Your Church Birdhouse

Leave the interior unfinished so birds can grip the walls. Seal the exterior with an exterior-grade stain or a water-based sealer, and allow it to cure fully before mounting. Mount the house 5 to 10 feet off the ground, facing away from prevailing winds and away from direct afternoon sun.

Clean the box after each nesting season. Remove old nesting material and check screws and hinges. Many owners find that a quick annual inspection extends the life of the house considerably.

  • Forstner bit set for a clean 1-1/8 inch entry hole without tear-out. View on Amazon
  • Exterior wood glue for joints that stay tight through wet seasons. View on Amazon
  • Stainless steel exterior screws that resist rust and staining from cedar. View on Amazon

Common mistakes to avoid

  • Using treated lumber or painting the interior, both of which can harm nesting birds.
  • Drilling an entry hole that is too large, which invites starlings and sparrows to take over.
  • Skipping drainage holes, which lets moisture build up and encourages mold.
  • Mounting the house in full sun, where the interior can overheat in summer.

FAQ

Are church birdhouse plans free to use for building at home?

Many woodworking sites and hobby publications offer free church-style plans for personal use. Check the license on any download, and avoid selling copies of plans you did not create.

What wood is best for a church birdhouse?

Cedar is a common choice because it resists rot and does not need chemical treatment. Untreated pine and other rot-resistant softwoods also work well.

How high should I mount a church birdhouse?

Most songbird houses perform well at 5 to 10 feet off the ground. Place it where cats cannot easily reach the entrance.

Conclusion

A church birdhouse is a practical project with a charming result. Use a 1-1/8 inch entry hole, untreated cedar and a clean assembly, and you will have a nest box that lasts for many seasons. Explore more designs in our guide to Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists if you want to build a second house.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.