Updated November 2026

DIY license plate birdhouse plans give you a sturdy nest box built from a flat metal plate, a few cedar or pine boards and basic hardware. This guide covers the cut list, assembly order and entry hole sizing so you finish with a birdhouse that stays dry and safe for chickadees, wrens or bluebirds. Most builders can complete the project in an afternoon with a few hand tools.

Materials and Cut List

Use a standard US license plate as the roof, since its flat, rust-resistant surface sheds water well. For the body, rough-sawn cedar or untreated pine at 3/4 inch thickness works well. Avoid pressure-treated lumber, because the chemicals can harm nesting birds.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • Front panel: 1 piece, 5-1/2 in. × 9 in.
  • Back panel: 1 piece, 5-1/2 in. × 12 in. (extra height helps it mount to a post or tree)
  • Side panels: 2 pieces, 4-1/2 in. × 9 in. with the top edges angled to match the roof slope
  • Floor: 1 piece, 4-1/2 in. × 4-1/2 in., with 4 drainage holes drilled, 1/4 in. each
  • Roof: 1 license plate, trimmed to 6 in. × 8 in. if needed

Step-by-Step Assembly

Cut and dry-fit the parts

Cut every board to length and check the fit before you drive any screws. Tilt the side panels so the top edge rests flat against the back of the license plate, then mark the angle with a square.

Drill the entry hole and ventilation

Mark the entry hole on the front panel about 6 to 7 inches above the floor. For chickadees and wrens, drill a 1-1/8 in. hole. For bluebirds, use 1-1/2 in. Drill two 1/4 in. ventilation holes near the top of each side panel.

Attach the sides, floor and back

Join the sides to the floor with exterior wood screws, then attach the front and back panels. Pre-drill each screw to prevent splitting cedar. Leave the front panel’s top edge slightly proud so the roof overhangs at least 1 inch on each side.

Mount the license plate roof

Secure the plate with 1-1/4 in. galvanized screws, placing one at each corner. Keep the screw heads outside the house so the interior stays smooth for birds.

Common Mistakes to Avoid

  • Skipping drainage holes in the floor, which lets water pool and rot the nest.
  • Using a hole size that is too large, which lets predators such as starlings or house cats reach in.
  • Mounting the house in full sun, which can overheat nestlings in summer.
  • Leaving sharp screw points inside the box where birds can injure themselves.
  • Painting the interior, since fumes and residue can harm chicks.
  • A pilot drill bit set, since pre-drilling keeps cedar from splitting around screws. View on Amazon
  • A hole saw kit in the 1-1/8 in. and 1-1/2 in. sizes, for clean entry holes. View on Amazon
  • Galvanized exterior screws, which resist rust from weather and the metal roof. View on Amazon

FAQ

Can I use a license plate from any state?

Yes, as long as the plate is intact and free of sharp, jagged edges. Trim any rough corners with tin snips and file them smooth before mounting.

What is the best mounting height?

Most small songbirds prefer a height of 5 to 10 feet, facing away from prevailing winds. Position the entry hole so the box faces east or southeast when possible.

How often should I clean the birdhouse?

Clean it once a year after the nesting season ends, removing old nesting material and scrubbing the floor with hot water. Avoid harsh chemical cleaners.

Conclusion

With the cut list, correct hole size and drainage in place, your license plate birdhouse will last several seasons. Adjust the entry hole to suit the species you want to attract. Check the house for wear each spring before the nesting season begins.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.