Updated November 2026

To round wood corners with a router, you fit a round-over bit, set the depth to remove a small amount of material per pass, and run the router along the edge so the bearing rides smoothly on the workpiece. The result is a consistent radius on each corner, which looks cleaner than sanding by hand and protects the edges from chipping. This guide covers the setup, the cutting sequence and the mistakes that cause tear-out.

What You Need Before You Start

A plunge or fixed-base router, a round-over bit with a bearing (a 1/4-inch radius is a good starting size for most furniture stock), a clamp or bench vise, and a few scrap pieces for test cuts. Make sure the stock is flat and firmly secured. Wear eye and hearing protection, and keep your hands clear of the bit at all times.

Shopping for one? See our guide: 5 Best Wood Router Prices: How Much Is a Wood Router? 5 Picks Compared.

How to Round Wood Corners with a Router

  1. Choose the right bit. A round-over bit with a bearing follows the edge of the board, so the radius stays even. Bits without a bearing require a fence or template and are better for longer, straight runs.
  2. Set the depth. Raise the bit so the bearing rides on the workpiece and only the cutting edge reaches the wood. For a 1/4-inch radius, you will usually cut about 1/4 inch deep in total.
  3. Test on scrap. Cut a sample from the same species and thickness. Check the radius with a square or a template before touching your project.
  4. Make the first pass shallow. Take roughly one-third of the total depth on the first pass, then the rest on a second pass. Shallow passes reduce tear-out and keep the router under control.
  5. Feed in the correct direction. Move the router counterclockwise around the edge of the piece. The bit should cut into the uncut wood rather than pulling away from it.
  6. Handle corners slowly. Slow down as you approach each corner. Let the bearing guide the bit around the curve, and avoid pausing with the bit spinning in one spot.

Working Through the Corners

If you are rounding all four corners of a panel, cut the end grain first. End grain tears out easily, and a second pass along the long grain will clean up any chipping on the corner. This order keeps the finished edges crisp.

Choosing the Right Radius and Depth

The radius you choose depends on the look and the use of the piece. Small radii protect edges without changing the profile much, while larger radii give a softer, more decorative appearance. Keep the router depth within the range the bit specifies, and never try to remove the full radius in a single pass.

Radius Typical Use Passes
1/8 inch Shelves, cabinet edges 1 pass
1/4 inch Tabletops, general furniture 2 passes
1/2 inch Decorative panels, chair seats 3 passes

Common Mistakes

  • Cutting the full radius in one pass, which causes burning and tear-out.
  • Feeding the router clockwise on an outside edge, which pulls the bit into the wood.
  • Letting the bearing ride off the edge, creating an uneven or flat spot.
  • Skipping the test cut on scrap wood.
  • Rounding corners before sanding the faces, which can leave dents to fix later.
  • Round-over bit with bearing – the bearing keeps the radius consistent along the edge. View on Amazon
  • Router edge guide or template guide – useful for controlling straight runs and repeat cuts. View on Amazon
  • Router clamp set – holds the workpiece steady so both hands stay on the router. View on Amazon

FAQ

Can I round wood corners without a bearing bit?

Yes, but you will need a fence or template to guide the router. Without one, the radius is hard to keep even, especially on curved corners.

Which way should I feed the router?

Feed counterclockwise around an outside edge so the bit cuts into uncut wood. Feeding the wrong way can cause kickback and chipping.

Should I sand after routing?

Light sanding with 150- to 180-grit paper removes router marks and smooths the radius. Sand only enough to clean the surface so the profile stays crisp.

Conclusion

Rounding wood corners with a router comes down to the right bit, shallow passes and the correct feed direction. Test your setup on scrap first, then work slowly around each corner. With practice, you will get clean, consistent radii on every project.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.