Updated November 2026

Learning how to cut curves in wood with a router comes down to one idea: guide the router’s base along a template or a fence while the bit removes material at a controlled depth. Once you set up the template, pick the right bit and feed in the correct direction, you can produce smooth arcs, circles and irregular shapes that match a pattern to within a few hundredths of an inch. This guide walks through the method, the setup and the mistakes that most often ruin a curve.

Choose the Right Method for Your Curve

Most curved router work uses one of two approaches. A template with a pattern bit is the most accurate option for repeat parts, because a bit with a bearing at the tip rides along the template edge and copies its shape exactly. A trammel or circle-cutting jig is better for true circles and arcs of a fixed radius, since it pivots the router around a center point. For one-off freehand shapes, you can use a bit with a bearing and a plywood guide, but accuracy depends heavily on your hand control.

Shopping for one? See our guide: 7 Best Router Bit to Cut Wood Options for Every Project (2026).

Step-by-Step: Cutting a Curve with a Template

  1. Make the template. Cut the shape from 1/4-inch or 3/8-inch plywood or MDF. Sand the edges smooth, since every bump gets copied into your workpiece.
  2. Attach the template to the blank. Use double-sided tape or screws placed outside the final cut line. Keep the template flush with the workpiece over the entire path.
  3. Select a pattern bit. A flush-trim bit with a top bearing works well when the bearing rides on the template and the cutting edge sits below it. Match the bearing diameter to the template offset you planned.
  4. Set the depth. Take multiple passes. A common approach is to remove no more than about 1/4 inch per pass in hardwood, going deeper only after the previous pass is clean.
  5. Feed against the rotation. Move the router counterclockwise around the outside of an external curve, and keep the bearing firmly against the template the whole time.
  6. Clean up the edges. Inspect for burn marks or tearout and follow with a sanding block or a small-radius file.

Setup Factors That Affect Curve Quality

Several settings control how smooth your curve turns out. Use the table below as a quick reference when planning a cut.

Factor What to Check Effect on the Curve
Bit rotation direction Feed against rotation Prevents the router from pulling away from the template
Depth per pass Shallow passes in hardwood Reduces burning and tearout
Feed speed Steady, not rushed Keeps the bearing in constant contact
Grain direction Read the grain before cutting Reduces splintering on tight radii
Template smoothness Sanded, with no flat spots Determines how smooth the final edge is

Tight curves with a small radius are harder than gentle arcs. If the radius is smaller than the bit’s cutting diameter, you will not be able to follow the path cleanly, so either use a smaller bit or cut the curve in stages.

Common Mistakes to Avoid

  • Taking too deep a cut in one pass, which causes burning and bit deflection.
  • Feeding with the rotation instead of against it, which can make the router grab and jump.
  • Skipping template sanding, so every flaw shows up in the finished part.
  • Letting the bearing lose contact with the template at the start or end of the cut.
  • Routing end grain or very short-grained areas without backing material, which invites chipping.

A template-cutting pattern bit with a top bearing is the core tool for this work, and it is worth matching the bearing diameter to your template plan. A plunge router with a fine depth adjustment makes it easier to take shallow passes without guessing. A router circle-cutting jig is useful if your project calls for consistent arcs. View on Amazon View on Amazon View on Amazon

If you want to build a fixed setup for repeat curved parts, read Wood Router Table Combo: How to Choose and Build One Step by Step (2026). For edge profiles that follow a curve, see How to Bevel Wood with a Router: 7 Best Picks Compared for 2026. Those working with templates on larger pieces may also find How to Flatten a Wood Slab with a Router: A Step-by-Step Guide useful.

FAQ

Can I cut a curve with a router without a template?

You can, using a bit with a bearing and careful freehand control, but accuracy is much lower. A template or jig gives repeatable results, especially for shapes you plan to duplicate.

Which direction should I feed the router for a curve?

Feed against the bit’s rotation. On an outside curve this usually means moving counterclockwise, which keeps the bearing pressed against the template.

How deep should each pass be when routing a curve in hardwood?

A common practice is about 1/4 inch per pass in hardwood, with deeper material removed over several passes. Shallow passes reduce burning and tearout.

Conclusion

Cutting curves with a router is mostly about preparation: a smooth template, the right pattern bit and a steady feed against the rotation. Work in shallow passes, check the grain and sand the template first, and your curves will come out cleaner. Consult a professional or the tool manufacturer’s manual if you are unsure about setup or safe operation.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.